Results 1 to 10 of 13
-
February 7th, 2009, 03:45 AM #1
PMAG problems for S&W M&P Carbine
I have read that the S&W M&P has had some problems with MAGPUL PMAGS not mating to the magazine weld. Have any of you experienced this problem?
-
February 7th, 2009, 10:23 AM #2
Re: PMAG problems for S&W M&P Carbine
not in over a year, some of the first M&P's didn't have their magwells opened up enough. now they do.
nothing to worry about anymore.
edit: nevermind, just saw one today that wouldn't take a PMAG, dunno why...it was brand new....Last edited by synergy; February 7th, 2009 at 09:55 PM.
-
February 7th, 2009, 10:48 AM #3
Re: PMAG problems for S&W M&P Carbine
I just got a 20 round Pmag that had been backordered.
I tried it out, and it does not drop free.
(Anvil Arms lower)
An older 30 round Pmag works just fine.
Hmmm... I have a box of about 8 brand new 30 rounders I haven't used yet... going to go check them now.I called to check my ZIP CODE!....DY-NO-MITE!!!
-
February 7th, 2009, 10:52 AM #4
Re: PMAG problems for S&W M&P Carbine
I had this problem in my M&P 15T. After blaming PMAG by S&W CS, I cited researches online that it was their carbines, I sent it back to S&W and they fixed the problem. I just got a few Thermold mags and those don't fit either. I am not happy with S&W so-called mil-spec claim. I'm debating whether or not to send the rifle in again for sell the mags back.
Al
-
February 7th, 2009, 11:11 AM #5
Re: PMAG problems for S&W M&P Carbine
You should send me that 20 rounder for testing and evaluation. If I find it doesn't work properly, I'll dispose of it for you!
-
February 7th, 2009, 11:17 AM #6
Re: PMAG problems for S&W M&P Carbine
OK, I just checked all my new 30 round Pmags, and they drop free,(Anvil Arms lower)so my issue is with the single 20 rd mag I currently own.
To the OP:
Sorry, I know my issue isn't related to an M&P, but wanted to note it as I had a similar issue. Thankfully, it doesn't seem to be gun related.I called to check my ZIP CODE!....DY-NO-MITE!!!
-
February 7th, 2009, 11:35 AM #7
Re: PMAG problems for S&W M&P Carbine
There are some tabs on the spine you can lightly file down or sand down and then they should drop free.
-
February 7th, 2009, 12:54 PM #8
Re: PMAG problems for S&W M&P Carbine
Warning: I may not read responses to OP before posting
-
February 7th, 2009, 12:57 PM #9
Re: PMAG problems for S&W M&P Carbine
I have experienced this same issue. 20 rnders do not drop free from multiple brand of lowers.
And this is the fix. Mine had flashing and overly generous corners on the rear rib. Hopefully MagPul will address this QC isue but it was simple enough to remedy._________________________________________
danbus wrote: ...Like I said before, I open carry because you don't, I fight for all my rights because
you won't, I will not sit with my thumb up my bum and complain, because you will.
-
February 7th, 2009, 01:04 PM #10
Similar Threads
-
magpul pmag 30
By tee-roy in forum GeneralReplies: 7Last Post: May 25th, 2010, 05:40 PM -
Orange Pmag
By ithinkimamedic in forum GeneralReplies: 2Last Post: February 7th, 2009, 01:55 AM -
WTS: DSA SA58 para carbine, M1 Carbine, and others, NM
By Oberfeld in forum GeneralReplies: 2Last Post: February 1st, 2008, 12:28 AM -
Charger for Magpul PMAG?
By Skullz in forum GeneralReplies: 1Last Post: January 10th, 2008, 02:31 AM -
magpul pmag test
By BFit70 in forum GeneralReplies: 5Last Post: December 26th, 2007, 09:02 AM
Bookmarks