Pennsylvania Firearm Owners Association

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.
Welcome to the Pennsylvania Firearm Owners Association Forum, we hope you like what you find here and we strongly encourage you to register for an account with us, especially if you are from Pennsylvania. Once registered you will have access to participate in our community. Thanks for visiting and we hope you become a regular!
Classifieds Rules
1. Put your ads in the right place
2. This is not eBay, include a price or a trade
3. You must wait at least 7 days to bump a classified thread
4. Do not break the law or offer to break the law
Read the full rules here, failing to follow them may result in your removal from the classifieds or the forum entirely.

Please Note: You can not reply to other people's classified ads, it is not a problem with your account. Contact them either via email or private message.

PAFOA provides space for this marketplace for non-prohibited persons to offer to sell or buy legal firearms with other non-prohibited persons. It is the responsibility of every seller and every buyer to comply with all state and federal laws, which includes verifying the buyer's state of residence, refusing sales to prohibited persons, and additional requirements. If you're not sure of the laws, find out. For maximum safety, we suggest doing all transfers of advertised guns through a Federal Firearms Licensee or a Sheriff; this is mandatory for handguns, and mandatory for sales to out-of-state residents, and it’s the only way you can get a PICS check done.

Requiring that your buyer show you a current PA License to Carry Firearms may provide some assurance that the buyer is not prohibited, but this is not foolproof. Being a registered user or someone that you've met personally is zero assurance of being non-prohibited for firearms possession.

Certain firearms, parts & accessories are also regulated by the National Firearms Act, so if you're not sure, do the research.

If you see an ad that you believe violates applicable laws, or if you believe you've been solicited to do an unlawful act, notify site administrators.
Attention! There has been an influx of scammer signups!

The method of operation is to private message you and tell you that you should contact such 'n such person at a given email address.

Please report the private messages. Staff will ban the offender, and I will implement an IP ban. Unfortunately these scammers are using VPN/proxy services, which may mean your VPN/proxy may be blocked.
Note - the old 3 day bump rule was changed to 7 days.
Attention! About VPN's and foreign IP addresses.

When signing up, do so from a US based Internet Service Provider. Turn off any VPN/safe-browsing feature. Failure to do so will result with your new account denied.

If you run into a IP ban afterwards as a member, again - turn off your VPN or switch servers. We do not ban legit Internet Service Providers from the USA(exception for certain individual IP addresses). Free VPN's tend to get banned too. We try not to ban legit subscription VPN services, but they rarely label their IP blocks correctly.

If you run into an IP ban, it likely wasn't you.

Results 1 to 1 of 1

Thread: Kydex forming press with etras

Thread Tools
Display
- Linear Mode
- Switch to Hybrid Mode
- Switch to Threaded Mode

October 18th, 2023, 06:57 PM #1
Gerrty

View Profile

View Forum Posts

Private Message

Junior Member
Join Date

Jan 2014

Location

gilbertsville, Pennsylvania
(Montgomery County)

Posts

15

Rep Power

0
Kydex forming press with etras
Hi everyone,
I am done forming the holsters and sheaths I needed, and my shop built Kydex press is gathering dust! If you are thinking of making your own holsters, knife sheaths, mag holders, light holders, belt clips etc. this press can do it. I am including a 12x12 sheet of 0.080" black kydex to get you going along with all my tooling, forms, patterns etc. for Glock 9mm mags, belt clips, AR mag forming, and a bunch of hardware. I'm asking $50 or trade for the following...

.223 brass
small rifle or pistol primers
Powder for .223/308
Let me know what you have, and thanks for looking!

Gerry

text= 484.644.8432
Attached Images

IMG_20231018_163716_copy_612x816_1.jpg (124.4 KB, 38 views)
IMG_20231018_164706_copy_612x816_1.jpg (145.2 KB, 34 views)
IMG_20231018_163747_copy_612x816_1.jpg (107.8 KB, 32 views)
IMG_20231018_163643_copy_612x816_1.jpg (90.1 KB, 29 views)
Reply With Quote