Pennsylvania Firearm Owners Association

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.
Welcome to the Pennsylvania Firearm Owners Association Forum, we hope you like what you find here and we strongly encourage you to register for an account with us, especially if you are from Pennsylvania. Once registered you will have access to participate in our community. Thanks for visiting and we hope you become a regular!
Attention! There has been an influx of scammer signups!

The method of operation is to private message you and tell you that you should contact such 'n such person at a given email address.

Please report the private messages. Staff will ban the offender, and I will implement an IP ban. Unfortunately these scammers are using VPN/proxy services, which may mean your VPN/proxy may be blocked.
Attention! About VPN's and foreign IP addresses.

When signing up, do so from a US based Internet Service Provider. Turn off any VPN/safe-browsing feature. Failure to do so will result with your new account denied.

If you run into a IP ban afterwards as a member, again - turn off your VPN or switch servers. We do not ban legit Internet Service Providers from the USA(exception for certain individual IP addresses). Free VPN's tend to get banned too. We try not to ban legit subscription VPN services, but they rarely label their IP blocks correctly.

If you run into an IP ban, it likely wasn't you.

Results 1 to 2 of 2

Thread: Gunsmith Needed: Install brake/Prep barrel on Remington 700

Thread Tools
Display
- Linear Mode
- Switch to Hybrid Mode
- Switch to Threaded Mode

May 11th, 2009, 05:41 AM #1
Fr0sty

View Profile

View Forum Posts

Private Message

Visit Homepage

Grand Member
Join Date

Oct 2007

Location

Lebanon, Pennsylvania
(Lebanon County)

Age

43

Posts

1,079

Rep Power

1051
Gunsmith Needed: Install brake/Prep barrel on Remington 700

Anyone know of a local smith that does good work on brake installs?

http://www.youtube.com/r1ngmasta

Reply With Quote
May 11th, 2009, 05:56 AM #2
zep_1

View Profile

View Forum Posts

Private Message

Member
Join Date

Apr 2008

Location

Hershey, Pennsylvania
(Dauphin County)

Posts

49

Rep Power

0
Re: Gunsmith Needed: Install brake/Prep barrel on Remington 700

Mark Bansner does alot of work on rem 700, he is in adamstown shouldn't be to far for ya.

http://www.bansnersrifle.com/

Reply With Quote

Quick Navigation General Top

Site Areas
Settings
Private Messages
Subscriptions
Who's Online
Search Forums
Forums Home
Forums
Forum
Discussion
Law & Politics
1. Pennsylvania
2. National
Marketplace
Events
Private Forums
1. PAFOA Club
Regions
1. Lake Erie Region
  1. Crawford
  2. Erie
  3. Mercer
  4. Venango
2. Allegheny National Forest Region
  1. Cameron
  2. Clarion
  3. Clearfield
  4. Elk
  5. Forest
  6. Jefferson
  7. McKean
  8. Potter
  9. Tioga
  10. Warren
3. Valleys of the Susquehanna Region
  1. Centre
  2. Clinton
  3. Columbia
  4. Juniata
  5. Lycoming
  6. Mifflin
  7. Montour
  8. Northumberland
  9. Snyder
  10. Union
4. Pocono Mountain Region
  1. Bradford
  2. Carbon
  3. Lackawanna
  4. Luzerne
  5. Monroe
  6. Pike
  7. Schuylkill
  8. Sullivan
  9. Susquehanna
  10. Wayne
  11. Wyoming
5. Lehigh Valley & Philadelphia Region
  1. Bucks
  2. Chester
  3. Delaware
  4. Lehigh
  5. Montgomery
  6. Northampton
  7. Philadelphia
6. PA Dutch Country/Hershey Region
  1. Adams
  2. Berks
  3. Cumberland
  4. Dauphin
  5. Franklin
  6. Lancaster
  7. Lebanon
  8. Perry
  9. York
7. Laurel Highlands Region
  1. Bedford
  2. Blair
  3. Cambria
  4. Fayette
  5. Fulton
  6. Greene
  7. Huntingdon
  8. Indiana
  9. Somerset
  10. Westmoreland
8. Pittsburgh Region
  1. Allegheny
  2. Armstrong
  3. Beaver
  4. Butler
  5. Lawrence
  6. Washington
Miscellaneous
1. The Lounge

« Previous Thread | Next Thread »

Similar Threads

Savage 111 7mm Remington Mag. 251/2” barrel with muzzle brake

By edstephan in forum General

Replies: 31
Last Post: October 24th, 2009, 08:38 PM
(Blair Co)Gunsmith needed for barrel work

By halo23pa in forum General

Replies: 3
Last Post: April 4th, 2009, 02:00 PM
gunsmith needed

By praharin in forum General

Replies: 0
Last Post: July 3rd, 2008, 04:54 PM
HELP need gunsmith to install front sight

By Chunky Monkey in forum General

Replies: 2
Last Post: August 16th, 2007, 07:57 PM
Gunsmith for nightsight install in PGH

By dirksterg30 in forum General

Replies: 11
Last Post: May 11th, 2007, 01:59 PM