Results 1 to 10 of 15
Thread: M1 Garand gunsmith
Hybrid View
-
June 30th, 2023, 05:05 PM #1Active Member
- Join Date
- Mar 2013
- Location
-
Lancaster,
Pennsylvania
(Lancaster County) - Posts
- 160
- Rep Power
- 462233
M1 Garand gunsmith
Looking for someone experienced in repairs on an M1 Garand. It is short stroking and not loading the next round when firing. The gas tube is clean and it is clear from the barrel. The end of the op-rod on a micrometer looks like it is within specs. I just put in a new Orion7 op spring. Still not working correctly. It passes the Tilt Test fine.
I am in South Central, PA. The Fulton Armory is about two hours away. I was told there is a good one near Duncannon. Any other suggestions? It needs more help than I can do right now.
-
June 30th, 2023, 05:41 PM #2Grand Member
- Join Date
- Jan 2013
- Location
-
Richboro,
Pennsylvania
(Bucks County) - Posts
- 3,081
- Rep Power
- 21474851
Re: M1 Garand gunsmith
Did this just start happening? Factory loads or reloads?
Is it short stroking so the next round in the clip just sits there on an empty chamber? Or does the round leave the clip and get hung up feeding?
-
June 30th, 2023, 05:53 PM #3
-
June 30th, 2023, 06:02 PM #4Grand Member
- Join Date
- Jan 2013
- Location
-
Richboro,
Pennsylvania
(Bucks County) - Posts
- 3,081
- Rep Power
- 21474851
-
July 1st, 2023, 08:31 AM #5Active Member
- Join Date
- Mar 2013
- Location
-
Lancaster,
Pennsylvania
(Lancaster County) - Posts
- 160
- Rep Power
- 462233
Re: M1 Garand gunsmith
As I had said, the gas tube is clear through to the barel, meaning the gas hole is clean. This is using factory American Eagle Garand loads. I need to check exactly what the inside dimensions should be on the gas tube, but with the op rod in place, there appears to be no visible light between the op rod and the sides of the gas tube. I am using a digital micrometer for all measurements.
The rifle cycles, the bolt gets reset so it is ready to fire the next round. It is not cycling back enough to strip off the next round to chamber it. I can manually cycle it and the round then does load correctly. I have two en bloc clips and it does this on both. I have been through all of the garand Youtubes and websites regarding this problem.
At this point, I am looking for a gunsmith in South Central PA who has experience on the Garand.
-
July 1st, 2023, 09:21 AM #6
Re: M1 Garand gunsmith
I have the gauges and spare parts and would be happy to do the troubleshooting and repair, but I'm 4h north-northwest of you. If you can't find anyone, I'll be in Carlisle 21-22 July and we could meet, I'll take it home and when finished ship it to back to you. I'd do it for current cost of parts and return shipping.
NoahWisdom and knowledge shall be the stability of thy times.
Similar Threads
-
Need to hire a gunsmith in my gunsmith shop
By jdb11 in forum GeneralReplies: 0Last Post: May 22nd, 2017, 06:47 PM -
WTS. Winchester M1 garand, HRA garand
By bthwb in forum GeneralReplies: 0Last Post: October 14th, 2008, 06:33 PM -
Looking for Gunsmith
By Montanya in forum GeneralReplies: 16Last Post: October 28th, 2007, 08:06 PM
Bookmarks