Pennsylvania Firearm Owners Association

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.
Welcome to the Pennsylvania Firearm Owners Association Forum, we hope you like what you find here and we strongly encourage you to register for an account with us, especially if you are from Pennsylvania. Once registered you will have access to participate in our community. Thanks for visiting and we hope you become a regular!
Attention! There has been an influx of scammer signups!

The method of operation is to private message you and tell you that you should contact such 'n such person at a given email address.

Please report the private messages. Staff will ban the offender, and I will implement an IP ban. Unfortunately these scammers are using VPN/proxy services, which may mean your VPN/proxy may be blocked.
Attention! About VPN's and foreign IP addresses.

When signing up, do so from a US based Internet Service Provider. Turn off any VPN/safe-browsing feature. Failure to do so will result with your new account denied.

If you run into a IP ban afterwards as a member, again - turn off your VPN or switch servers. We do not ban legit Internet Service Providers from the USA(exception for certain individual IP addresses). Free VPN's tend to get banned too. We try not to ban legit subscription VPN services, but they rarely label their IP blocks correctly.

If you run into an IP ban, it likely wasn't you.

Results 1 to 2 of 2

Thread: Drilling and tapping a Maverick 88

Thread Tools
Display
- Linear Mode
- Switch to Hybrid Mode
- Switch to Threaded Mode

May 26th, 2023, 03:58 PM #1
ViperGTS19801

View Profile

View Forum Posts

Private Message

Grand Member
Join Date

Jan 2010

Location

Media, PA, Pennsylvania
(Delaware County)

Age

38

Posts

4,149

Rep Power

20343748
Drilling and tapping a Maverick 88

I have a Maverick 88, and a sidesaddle to go with it, but the latter needs holes drilled and tapped in the former for them to marry. Who's the best place in the Lehigh Valley to go to for this to get it done properly?

Junior

Reply With Quote
May 26th, 2023, 04:06 PM #2
HanzMcFeely

View Profile

View Forum Posts

Private Message

Grand Member
Join Date

Jul 2020

Location

Child of the corn, Pennsylvania

Posts

1,271

Rep Power

21474841
Re: Drilling and tapping a Maverick 88

Handgunner in Topton. He’s reasonably priced and knows what he’s doing. Last drill/tap/sight install job he did for me was $40 (win mod 94 williams 5d)

Reply With Quote

Quick Navigation Gunsmithing Top

Site Areas
Settings
Private Messages
Subscriptions
Who's Online
Search Forums
Forums Home
Forums
Forum
Discussion
Law & Politics
1. Pennsylvania
2. National
Marketplace
Events
Private Forums
1. PAFOA Club
Regions
1. Lake Erie Region
  1. Crawford
  2. Erie
  3. Mercer
  4. Venango
2. Allegheny National Forest Region
  1. Cameron
  2. Clarion
  3. Clearfield
  4. Elk
  5. Forest
  6. Jefferson
  7. McKean
  8. Potter
  9. Tioga
  10. Warren
3. Valleys of the Susquehanna Region
  1. Centre
  2. Clinton
  3. Columbia
  4. Juniata
  5. Lycoming
  6. Mifflin
  7. Montour
  8. Northumberland
  9. Snyder
  10. Union
4. Pocono Mountain Region
  1. Bradford
  2. Carbon
  3. Lackawanna
  4. Luzerne
  5. Monroe
  6. Pike
  7. Schuylkill
  8. Sullivan
  9. Susquehanna
  10. Wayne
  11. Wyoming
5. Lehigh Valley & Philadelphia Region
  1. Bucks
  2. Chester
  3. Delaware
  4. Lehigh
  5. Montgomery
  6. Northampton
  7. Philadelphia
6. PA Dutch Country/Hershey Region
  1. Adams
  2. Berks
  3. Cumberland
  4. Dauphin
  5. Franklin
  6. Lancaster
  7. Lebanon
  8. Perry
  9. York
7. Laurel Highlands Region
  1. Bedford
  2. Blair
  3. Cambria
  4. Fayette
  5. Fulton
  6. Greene
  7. Huntingdon
  8. Indiana
  9. Somerset
  10. Westmoreland
8. Pittsburgh Region
  1. Allegheny
  2. Armstrong
  3. Beaver
  4. Butler
  5. Lawrence
  6. Washington
Miscellaneous
1. The Lounge

« Previous Thread | Next Thread »

Similar Threads

Drilling and tapping Heritage Rough Rider for scope mounts?

By 4thdimension in forum Gunsmithing

Replies: 10
Last Post: June 25th, 2017, 06:20 PM
drilling/tapping an old shotgun

By Captain4 in forum Gunsmithing

Replies: 1
Last Post: October 17th, 2013, 05:38 PM
HB 2400 - PA big brother wire tapping bill - UPGRADE

By WhiteFeather in forum Pennsylvania

Replies: 67
Last Post: December 5th, 2012, 08:43 AM
ar-15 drilling jig

By fordmech00 in forum General

Replies: 10
Last Post: May 17th, 2009, 08:55 AM
Drilling and Tapping Mossy 500

By wjh2657 in forum General

Replies: 4
Last Post: December 27th, 2008, 01:28 AM