Pennsylvania Firearm Owners Association

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.
Welcome to the Pennsylvania Firearm Owners Association Forum, we hope you like what you find here and we strongly encourage you to register for an account with us, especially if you are from Pennsylvania. Once registered you will have access to participate in our community. Thanks for visiting and we hope you become a regular!
Attention! There has been an influx of scammer signups!

The method of operation is to private message you and tell you that you should contact such 'n such person at a given email address.

Please report the private messages. Staff will ban the offender, and I will implement an IP ban. Unfortunately these scammers are using VPN/proxy services, which may mean your VPN/proxy may be blocked.
Attention! About VPN's and foreign IP addresses.

When signing up, do so from a US based Internet Service Provider. Turn off any VPN/safe-browsing feature. Failure to do so will result with your new account denied.

If you run into a IP ban afterwards as a member, again - turn off your VPN or switch servers. We do not ban legit Internet Service Providers from the USA(exception for certain individual IP addresses). Free VPN's tend to get banned too. We try not to ban legit subscription VPN services, but they rarely label their IP blocks correctly.

If you run into an IP ban, it likely wasn't you.

Results 1 to 10 of 79

Thread: Need Input for Building a .338 WINMAG Round

Thread Tools
Display
- Switch to Linear Mode
- Switch to Hybrid Mode
- Threaded Mode

Threaded View

April 19th, 2022, 08:11 AM #1
Walleye Hunter

View Profile

View Forum Posts

Private Message

Master Member
Join Date

Oct 2012

Location

Douglassville, Pennsylvania
(Berks County)

Posts

11,820

Rep Power

21474859
Need Input for Building a .338 WINMAG Round

OK, I have some questions here...I have a Winchester Model 70 in .338 WINMAG, that I want to take to Thunder Valley for long range training. But first I need to create my round for it. I have accumulated everything I need to reload for it and believe I have the process figured out. Now I need some help. For powder, I have W760 ball, 4831 in IMR and H, and IMR 4451, all of which I believe are suitable powders. I have Hornady 200 gr and 225 gr bullets and have both LR and LRM primers. Oh...I only have 1 lb each on the powders. Also, will there be enough in 1 lb to develop and load 100 rounds? And which powder and bullet would be best?

I'm sure I'll have more questions later.

Last edited by Walleye Hunter; September 6th, 2022 at 07:25 AM. Reason: Adjust title for ease in searching

Gender confusion is a mental illness

Reply With Quote

Quick Navigation Ammunition & Reloading Top

Site Areas
Settings
Private Messages
Subscriptions
Who's Online
Search Forums
Forums Home
Forums
Forum
Discussion
Law & Politics
1. Pennsylvania
2. National
Marketplace
Events
Private Forums
1. PAFOA Club
Regions
1. Lake Erie Region
  1. Crawford
  2. Erie
  3. Mercer
  4. Venango
2. Allegheny National Forest Region
  1. Cameron
  2. Clarion
  3. Clearfield
  4. Elk
  5. Forest
  6. Jefferson
  7. McKean
  8. Potter
  9. Tioga
  10. Warren
3. Valleys of the Susquehanna Region
  1. Centre
  2. Clinton
  3. Columbia
  4. Juniata
  5. Lycoming
  6. Mifflin
  7. Montour
  8. Northumberland
  9. Snyder
  10. Union
4. Pocono Mountain Region
  1. Bradford
  2. Carbon
  3. Lackawanna
  4. Luzerne
  5. Monroe
  6. Pike
  7. Schuylkill
  8. Sullivan
  9. Susquehanna
  10. Wayne
  11. Wyoming
5. Lehigh Valley & Philadelphia Region
  1. Bucks
  2. Chester
  3. Delaware
  4. Lehigh
  5. Montgomery
  6. Northampton
  7. Philadelphia
6. PA Dutch Country/Hershey Region
  1. Adams
  2. Berks
  3. Cumberland
  4. Dauphin
  5. Franklin
  6. Lancaster
  7. Lebanon
  8. Perry
  9. York
7. Laurel Highlands Region
  1. Bedford
  2. Blair
  3. Cambria
  4. Fayette
  5. Fulton
  6. Greene
  7. Huntingdon
  8. Indiana
  9. Somerset
  10. Westmoreland
8. Pittsburgh Region
  1. Allegheny
  2. Armstrong
  3. Beaver
  4. Butler
  5. Lawrence
  6. Washington
Miscellaneous
1. The Lounge

« Previous Thread | Next Thread »

Similar Threads

Need Some Input!

By RBA02 in forum General

Replies: 35
Last Post: April 13th, 2013, 05:09 AM
Thinking of Building an AR any input?

By DoubleSawbuck in forum Rifles

Replies: 4
Last Post: July 26th, 2012, 09:17 PM
Need input on Glock 9 mm Scherer 31 round mags.

By bripro in forum Pistols

Replies: 5
Last Post: April 27th, 2012, 01:57 AM
OK so how about a little LEO input...

By Snert in forum General

Replies: 11
Last Post: November 9th, 2009, 09:24 PM