Results 1 to 10 of 16
-
February 19th, 2021, 12:34 PM #1Super Member
- Join Date
- Jun 2012
- Location
-
Honesdale,
Pennsylvania
(Wayne County) - Posts
- 694
- Rep Power
- 2990182
Polymer 80 glock end plate installation
I'm trying to put together a polymer80 Glock 19 i picked up from JSD.
I'm at the last step of the glock slide assembly where you push down the extractor spring and firing pin assembly to slide the end plate in. I have the end plate over both, but it wont slide forward all the way to snap into place. No matter how hard I push to get the end plate to snap into place and flush with the slide it wont go.
I tried taking out the extractor spring, leaving the firing pin assembly, to see if the end plate will completely go and it does.
Any suggestions what I can do or what the problem is?
-
February 19th, 2021, 01:03 PM #2
Re: Polymer 80 glock end plate installation
Hmm. Is your channel liner installed all the way in? Make sure the extractor spring is installed in the correct direction - make sure the metal end of the extractor spring is pushing on the extractor, not the reverse.
Also check your firing pin safety plunger isn't binding. I don't think this would impact what you're trying to do here but it's definitely something to watch out for that the spring isn't all hung up in the hole.
-
February 19th, 2021, 01:12 PM #3Super Member
- Join Date
- Jun 2012
- Location
-
Honesdale,
Pennsylvania
(Wayne County) - Posts
- 694
- Rep Power
- 2990182
Re: Polymer 80 glock end plate installation
When the firing pin assembly and extractor spring/rod is in, i cannot press down on the safety plunger, is that the way it should be?
-
February 19th, 2021, 05:57 PM #4Super Member
- Join Date
- Feb 2015
- Location
-
Montco,
Pennsylvania
(Montgomery County) - Posts
- 864
- Rep Power
- 21474846
Re: Polymer 80 glock end plate installation
Be sure to push down on the little plastic piece BELOW the firing pin catch (on the underside of the slide). Makes pushing the end plate in way easier.
-
February 19th, 2021, 06:20 PM #5Grand Member
- Join Date
- Jul 2020
- Location
-
Child of the corn,
Pennsylvania
- Posts
- 1,271
- Rep Power
- 21474841
Re: Polymer 80 glock end plate installation
Second this. And the channel liner Is seated fully.
Depending on your slide, the plate can be a bit tight to install.
Are you using a real OEM glock channel liner? The aftermarket ones are kinda junk. Make sure to clean up the little plastic nib leftover from the molding process and that you are installing it in the correct orientation.
If you are close, I have a channel liner tool you can borrow. Or if you want to pay the shipping to/from I can mail it to you
-
February 19th, 2021, 08:59 PM #6Super Member
- Join Date
- Jun 2012
- Location
-
Honesdale,
Pennsylvania
(Wayne County) - Posts
- 694
- Rep Power
- 2990182
-
February 19th, 2021, 10:17 PM #7Grand Member
- Join Date
- Jul 2020
- Location
-
Child of the corn,
Pennsylvania
- Posts
- 1,271
- Rep Power
- 21474841
-
February 20th, 2021, 12:01 AM #8Super Member
- Join Date
- Jun 2012
- Location
-
Honesdale,
Pennsylvania
(Wayne County) - Posts
- 694
- Rep Power
- 2990182
Re: Polymer 80 glock end plate installation
I just tried pressing on the firing pin assembly sleeve under the slide while pushing the end plate, still wont go in. I think the issue is with the extractor spring/rod. When I take the extractor spring/rod out the end plate goes in fine.
-
February 20th, 2021, 12:03 AM #9Grand Member
- Join Date
- Dec 2011
- Location
-
Where the amish roam,
Pennsylvania
(Lancaster County) - Posts
- 2,812
- Rep Power
- 21474851
Re: Polymer 80 glock end plate installation
Join here shoot me a message (Rocky Decatur) when you do so I can approve you right away to join the group someone there can help and you can post up photos and videos.
https://www.facebook.com/groups/mastergunbuilders
-
February 20th, 2021, 10:34 AM #10Super Member
- Join Date
- Jun 2012
- Location
-
Honesdale,
Pennsylvania
(Wayne County) - Posts
- 694
- Rep Power
- 2990182
Similar Threads
-
Polymer 80 Glock build
By solrac7 in forum PistolsReplies: 18Last Post: February 12th, 2019, 11:54 AM -
Glock sight installation in Blair county??
By Squatchy in forum PistolsReplies: 3Last Post: June 1st, 2015, 09:03 PM -
Glock Sight Installation!
By Everlastingfate in forum GunsmithingReplies: 27Last Post: November 10th, 2013, 12:50 PM -
Glock nightsight installation in South East PA?
By Kb! Bob in forum GeneralReplies: 11Last Post: December 28th, 2009, 02:12 PM
Bookmarks