Results 1 to 4 of 4
Thread: New to area.. help please!
-
September 8th, 2020, 03:40 PM #1Junior Member
- Join Date
- Feb 2020
- Location
-
Clifton,
New Jersey
- Posts
- 3
- Rep Power
- 0
New to area.. help please!
Hello
Just moved to Center City area from NJ. I purchased an AR lower and some parts recently that i want to put together however I don’t have a vice and don’t think I want to purchase one ( for space reasons). Anyone willing and able to invite me in to use theirs?
I will provide beer and happy to throw you a couple bucks for the help!
Alternatively does anyone know a good Smith in the area? Searched a bit but all the threads were from years ago.
Final question: any FFLA in the area who will accept forearms shipped from individuals?
Thank you so much!
-Quinn
-
September 8th, 2020, 03:54 PM #2
Re: New to area.. help please!
Hi, Quinn! Welcome! Glad you got out of the Peoples Republic of NJ, but Philly isn't much better, I'm afraid.
First of all, a vice is not a necessity to build an AR lower, although I admit it can make it easier. If you want to build your own upper, definitely need one and a special set of blocks that go inside the upper receiver so you don't crush it. Here's a video of a guy who put his lower together without a vice.
https://www.youtube.com/watch?v=nen5iNNzVXE
If you really want to use a bench with a vise on it, you're more than welcome to come use mine, I'm out by Valley Forge, though, not too close. My son and I have built about 8 of them, so if this is your first, happy to help in any way I can.
Couple of suggestions, if I may be so bold and you don't have all your parts yet ...
Get an ALG Defense ACT trigger. They're only about $65, but such an improvement over the stock kit triggers you won't believe it. They are MILSPEC dimensions, but the sear/hammer surfaces that work together are polished and then differentially coated, one with nickel boron, one with nickel teflon. You can also buy a lower parts kit without a trigger, because this is commonly done.
An H buffer will give you better results than the stock carbine buffer, the little extra weight helps smooth everything out.
-
October 2nd, 2020, 12:38 PM #3Junior Member
- Join Date
- Feb 2020
- Location
-
Clifton,
New Jersey
- Posts
- 3
- Rep Power
- 0
Re: New to area.. help please!
Thank you so much for the offer JCinPA. I’ll keep you in mind if I need you.
I think I will be able to assemble without a vice. I went with a complete upper and I am giving a ratcheting castle but a try so I should be able to complete it without a vice.
I have all the parts. However I had a stripped lower shipped to Founding Fathers Weapon outfitters. It has been marked delivered for close to two weeks. I showed up expecting to be able to pick it up but they told me they are backed up. I have them the weekend thinking I would hear back but I did not. I have called a multitude of times just asking if it has arrived safely, but they are unable to give me a straight answer and just say that they are opening boxes.
Every firearm I ever had shipped to a FFL would call me the same day it arrived. Should I be concerned?
-
October 2nd, 2020, 06:57 PM #4
Re: New to area.. help please!
Seconding what JCinPA said about not needing a vice to build a lower, your best friends are YouTube, patience and a large, clear plastic bag to work inside of when attempting to install the front take-down pin's spring and detent, along with a large magnet to find the detent when it flies out of the bag.
Last edited by eatmydust; October 2nd, 2020 at 07:49 PM.
Similar Threads
-
Bucks County Area Pawn Shops with Firearms Quakertown Doylestown Warminster area ?
By Raystown in forum ShopsReplies: 7Last Post: February 6th, 2016, 09:01 PM -
Anyone in the area have an XDs?
By fonz in forum CentreReplies: 2Last Post: June 10th, 2013, 07:05 PM -
New to Area
By Horus in forum MercerReplies: 2Last Post: March 27th, 2013, 09:19 PM
Bookmarks