Results 1 to 10 of 16
-
May 20th, 2020, 08:49 PM #1
Miculek competition lifter for Mossberg 930!
This is a MUST HAVE upgrade for the 930! For 9 years now I've lived with the cutout at the end of the lifter, tried to load with a bent thumb, and had my thumb eaten but no longer. Jerry's website had this in stock and ready to ship so I got it without a second thought. Here are some photos. I noticed that since it's slightly longer, this will catch on a factory follower. The bump at the end of the follower sticks out a bit too far and when you push the lifter up on an empty mag, it stays up because it's trapped there. Now, you can file a small amount off of the end of the lifter or change your follower. Considering the lifter cost $58 shipped and you can get a new magazine follower for about a third of that, I'd suggest changing the follower. I switched to a generic stainless steel follower I had in a spare parts bin and the bump sticks out slightly less so the lifter doesn't get stuck. Installation took a few minutes but most of that was because I turned the trigger assembly on the side and the hammer pin fell out so I had to look for it. I admit that $50 plus is not inexpensive but I think it's worth every penny. If your 930 rarely sees any action or if you have unusually plump thumbs that don't get caught, maybe it's not worth it for you but this is the shotgun I shoot the most and it's absolutely worth it for me.
13 in stock as of this post.
https://miculek.com/product/miculek-...evator-lifter/
-
May 20th, 2020, 09:13 PM #2
Re: Miculek competition lifter for Mossberg 930!
Nice...
I had mine welded up about 4 years ago.
-
May 21st, 2020, 09:41 AM #3Grand Member
- Join Date
- Aug 2011
- Location
-
Moscow,
Pennsylvania
(Lackawanna County) - Posts
- 4,029
- Rep Power
- 21474853
Re: Miculek competition lifter for Mossberg 930!
It’s definitely a must have
Or3gun spends a ton of time working on the reliability of these things
-
May 21st, 2020, 12:21 PM #4
-
May 21st, 2020, 02:06 PM #5Member
- Join Date
- Apr 2020
- Location
-
Nunya,
Pennsylvania
(Montgomery County) - Posts
- 33
- Rep Power
- 0
-
May 21st, 2020, 03:25 PM #6
-
May 21st, 2020, 06:09 PM #7Member
- Join Date
- Apr 2020
- Location
-
Nunya,
Pennsylvania
(Montgomery County) - Posts
- 33
- Rep Power
- 0
Re: Miculek competition lifter for Mossberg 930!
-
May 21st, 2020, 11:28 PM #8
-
May 21st, 2020, 11:41 PM #9
Re: Miculek competition lifter for Mossberg 930!
Sadly, you will need all of what Or3gun sells to get the 930 to run...most of the time. My 930SPX ran great for years and then it stopped being reliable. Failures to feed and failures to eject, mostly. I did everything in the book to get it back to working order. Sent it to Mossberg, said it was fixed, it wasn't. I replaced every spring, cleaned every inch, etc. Installed the Multi-Use Essentials Combo Kit from Or3gun and the gun now runs again. It's more ammo sensitive now than before, but I can get through a match with minimal issues.
My wife is next in line for a new shotgun. Then it's my turn, and I'm eyeing up a Beretta 1301 to replace the 930SPX.
-
May 22nd, 2020, 08:58 AM #10Grand Member
- Join Date
- Aug 2011
- Location
-
Moscow,
Pennsylvania
(Lackawanna County) - Posts
- 4,029
- Rep Power
- 21474853
Similar Threads
-
Welding Extra Material On Mossberg 930 Lifter?
By Misery Loves Shotguns in forum ShotgunsReplies: 3Last Post: February 17th, 2019, 11:57 AM -
Jerry Miculek "De-Locked" his competition revolver!!!
By Steve_NEPhila in forum PistolsReplies: 14Last Post: July 16th, 2010, 10:37 AM
Bookmarks