Results 1 to 10 of 24
Thread: AR build shot the detent
-
August 9th, 2014, 03:55 PM #1
AR build shot the detent
Dam I knew I was going to before I did but I still went ahead and started assembling my lower and ting I shot the detent for the front takedown pin into another dimension. If I was showing a friend I would have used precautions, but for myself ahh just send it into the twilight zone. Why can you hear tiny parts hit and bounce around but never find them? Order sent to PSA.
-
August 9th, 2014, 04:02 PM #2
Re: AR build shot the detent
I have crawled around my floor with a flashlight for over an hour. I have yet to lose any of those little pieces, they will not win.
"A man who has nothing for which he is willing to fight, nothing which is more important than his own personal safety, is a miserable creature and has no chance of being free unless made and kept so by the exertions of better men than himself"
"He created the game, played the game, and lost the game.... All under his own terms, by his own doing." JW34
"Tolerance is the lube that helps slip the dildo of dysfunction into the ass of a civilized society." Plato
-
August 9th, 2014, 04:11 PM #3
Re: AR build shot the detent
It's eating at me. I thought I'd make the feeling go away by ordering replacements. It ain't working. by the way PSA has a few good deals today. $$$ working over deep carpet is a bad idea.
-
August 9th, 2014, 04:35 PM #4
Re: AR build shot the detent
I usually end up finding the "lost" part later after the replacement has arrived.
I've also noticed on my last couple builds,the Spikes LPK W/O trigger assembly
has an extra detent and spring.
Nice for those of us with sometimes less than nimble fingers.
Not sure if the extras are intentional or not.Μολὼν λαβέ
Don't pick a fight with an old man. If he is too old to fight, he'll just kill you.
-
August 9th, 2014, 04:36 PM #5
Re: AR build shot the detent
I always sleep with my guns when you are gone
-
August 9th, 2014, 04:47 PM #6Grand Member
- Join Date
- Aug 2011
- Location
-
Moscow,
Pennsylvania
(Lackawanna County) - Posts
- 4,029
- Rep Power
- 21474853
Re: AR build shot the detent
The last one I did flew out hit the ceiling bounced off and ended up in the chandelier in the dining room. Good thing the wife wasn't home,
-
August 9th, 2014, 05:30 PM #7
Re: AR build shot the detent
I've been known to install that part sitting in the bath tub with the drain plugged and curtain closed. No escapees so far.
-
August 9th, 2014, 06:42 PM #8
Re: AR build shot the detent
I have purchased a tool to make it easier to install the front detent pin.
Consists of a knurled ended rod,with a hole for the pin and spring to fit through,that fits through the front pivot pin hole from the opposite side.
Compress the spring/pin combination through the hole,slide the tool back
slightly,which holds the detent and spring in place,and install the pivot pin,which captures cursed flying parts in place.
Not 100% fool proof,but pretty close.Μολὼν λαβέ
Don't pick a fight with an old man. If he is too old to fight, he'll just kill you.
-
August 9th, 2014, 07:04 PM #9
Re: AR build shot the detent
I use a similar device. A pin with holes from Tractor Supply that fits the hole loosely. (Not sure of the proper name). Push the spring and detent down in with a punch, rotate the pin slightly keeping downward pressure, remove the punch, rotate the pin slightly more and use the pivot pin to push out the Tractor supply pin.
Easy!
-
August 9th, 2014, 08:23 PM #10Banned
- Join Date
- Jan 2009
- Location
-
S.W. Pa,
Pennsylvania
(Westmoreland County) - Posts
- 1,188
- Rep Power
- 0
Similar Threads
-
Charger Safety Detent Plunger Spring
By RLS in forum GeneralReplies: 0Last Post: November 4th, 2009, 12:30 AM -
Smith Wanted: pivot pin detent hole drill
By avizpls in forum GeneralReplies: 22Last Post: February 10th, 2007, 12:27 PM
Bookmarks