Results 1 to 10 of 17
-
June 14th, 2013, 11:35 PM #1
Springfield Armory 1911's - WTH???
Just looked at the line of 1911 pistols from Springfield for 2013. No 3" 1911's any longer? WTH? Where'd they go?
Are they now forcing everyone into either an XDS or EMP?
-
June 14th, 2013, 11:44 PM #2
-
June 14th, 2013, 11:52 PM #3Grand Member
- Join Date
- Dec 2010
- Location
-
back to Port Charlotte,
Florida
- Age
- 60
- Posts
- 5,483
- Rep Power
- 3627622
Re: Springfield Armory 1911's - WTH???
Are you talking about a .45 3"?
BCM and Glock...for a bigger pile of 'cold dead hands' brass.
-
June 15th, 2013, 01:28 AM #4
Re: Springfield Armory 1911's - WTH???
Who cares?
3 inch 1911, asking for trouble.Selling off a a sizeable Spyderco collection here
-
June 15th, 2013, 07:43 AM #5Grand Member
- Join Date
- Dec 2010
- Location
-
back to Port Charlotte,
Florida
- Age
- 60
- Posts
- 5,483
- Rep Power
- 3627622
Re: Springfield Armory 1911's - WTH???
Very true in some cases.
Super short 1911's definitely are not for everyone. If you are used to shooting pistols that are on the forgiving side, whether full size, or carry; you likely will not like a short barrel 1911. If a person understands why the short barrel is harder to shoot than a long barrel, they have a better chance of getting the short barreled 1911 to work right.
The short barrel of a 1911 drops at a steeper angle than the longer barreled version does, which in turn changes the geometry of the feed ramp, and makes it steeper. There is also more force, or binding, on the muzzle of the barrel at that angle, which is why a bushing is not used on a short barrel. It just will not succumb to that steeper angle when the barrel unlocks from the slide.
The slide is smaller and lighter and will not have the same momentum that a heavier, full size slide will have. Also, the slide has to pick up a new round right against it. There is no momentum building as the breech face comes in contact with the new round. It has to rely solely on the strength of the recoil spring to pull the round out of the mag and then pull it into the chamber, yet the spring cannot be so strong that it will not fully cycle under recoil with standard power ammo. If you're using a magazine that doesn't have a strong spring in it, then you're going to be dead in the water right there. The follower spring has to be strong enough to get the new round up and ready to pull out in time where with a 5" 1911, there are a couple extra milliseconds before the breech contacts the new round.
There is an ultra fine balance in getting all these angles and spring rates to work optimally. Fortunately, those that are building these little buggers, today, have it sorted out. What they cannot do is make an individual shoot the gun like it needs to be for all these things to come together at the exact moment (or perfect timing). If you want to use weak ammo (hand loads, say...) or you insist on a relaxed grip, then you'd be wise to stay clear of the ultra short barreled 1911's. Tweaking anything on one to get it to shoot under a relaxed grip or cool ammo will do nothing but cause the slide to beat the shit out of the frame and you're still going to end up with an $800 to $1200 paper weight.
ETA - I have handled and shot a number of Kimber short barrel 1911's. My best friend has had one now for about 6 months and it makes him grin every time he dumps a mag through it...and nothing gets this dude to grin, much. You can definitely get it to easily malfunction if you purposely try to.Last edited by harold63; June 15th, 2013 at 07:50 AM.
BCM and Glock...for a bigger pile of 'cold dead hands' brass.
-
June 15th, 2013, 09:54 AM #6
Re: Springfield Armory 1911's - WTH???
Yes, I was referring to all of Springfield's shorter than 5" barrel 1911's. They used to list a complete array of 3" and 4" 1911's. Not any more, they only have one 4" Champion listed, the rest are gone as well as all of the 3" models.
This is where I was going with are they forcing everyone who wants a short barrelled model to either go with an EMP or out of 1911's altogether with their XD line.
Glad I bought my GI Micro when I did, then. Just wish I had never sold my GI Champion.
I understand about the compacts being more problematic, but it's always nice to have affordable options out there. The 5" and Commander size pistols may work for everyone, and I have carried them before, but being only 5' 6", they're a little bulky for me to lug around all day.
-
June 15th, 2013, 10:15 AM #7Grand Member
- Join Date
- Dec 2010
- Location
-
back to Port Charlotte,
Florida
- Age
- 60
- Posts
- 5,483
- Rep Power
- 3627622
Re: Springfield Armory 1911's - WTH???
Dude, I'm 6ft 195lbs, and they are bulky for me. The Mrs. and I are both looking at the Kimber line of 3 inchers. You can find some used SA short barrel 1911's out there, and yes; they are much more cost friendly than the Kimbers. http://www.armslist.com/posts/174713...t--45-cal-1911
ETA - every micro SA 1911 in .45 I found has been sold, so it looks as if they are a little harder to find than the 3.5" model.Last edited by harold63; June 15th, 2013 at 10:19 AM.
BCM and Glock...for a bigger pile of 'cold dead hands' brass.
-
June 15th, 2013, 11:19 AM #8Active Member
- Join Date
- Oct 2009
- Location
-
Sellersville,
Pennsylvania
(Bucks County) - Posts
- 134
- Rep Power
- 1415
Re: Springfield Armory 1911's - WTH???
-
June 15th, 2013, 11:25 AM #9Grand Member
- Join Date
- Dec 2010
- Location
-
back to Port Charlotte,
Florida
- Age
- 60
- Posts
- 5,483
- Rep Power
- 3627622
-
June 15th, 2013, 11:34 AM #10
Re: Springfield Armory 1911's - WTH???
Similar Threads
-
Springfield Armory 1911 MC Operator vs. SIG Sauer Blackwater 1911.Who's the TOP DAWG?
By Nickname Tactical in forum PistolsReplies: 30Last Post: August 29th, 2010, 04:49 PM -
Thoughts On The Springfield Armory 1911 Operator? Purchasing My First 1911.
By Nickname Tactical in forum PistolsReplies: 4Last Post: January 19th, 2010, 11:12 AM
Bookmarks