Results 1 to 10 of 29
Thread: ejection problems
-
May 8th, 2013, 09:14 PM #1Member
- Join Date
- May 2013
- Location
-
derry,
Pennsylvania
(Westmoreland County) - Posts
- 56
- Rep Power
- 870
ejection problems
I got a Taurus 605 poly protector and I have to say I got no complaints except one. 2-3 of the five casings like to only go as far as the ejector can push em and I have to pull em out the rest of the way by hand. I don't want to send it in and go through the trouble for a problem that may not get fixed. Does anyone have any ideas to remedy this issue?
-
May 8th, 2013, 09:28 PM #2
Re: ejection problems
what brand ammo are ya using?
-
May 8th, 2013, 10:06 PM #3Member
- Join Date
- May 2013
- Location
-
derry,
Pennsylvania
(Westmoreland County) - Posts
- 56
- Rep Power
- 870
Re: ejection problems
I've tried pmc bronze and Remington. I have a box of federal but im hesitant to shoot until I get more cuz of the lead drought
-
May 19th, 2013, 02:35 PM #4Active Member
- Join Date
- Aug 2011
- Location
-
S,
Pennsylvania
(Delaware County) - Posts
- 121
- Rep Power
- 1962
Re: ejection problems
Does it load easy, or do the same 2-3 chambers require pressure? What does the brass look like that hangs up? Are you shooting 38 or 357?
-
May 26th, 2013, 02:18 PM #5Member
- Join Date
- May 2013
- Location
-
derry,
Pennsylvania
(Westmoreland County) - Posts
- 56
- Rep Power
- 870
Re: ejection problems
It loads just fine and the casings look ok. I shot some of that federal and all casings hung up out of 5 shots. Very sticky and disappointing considering they were expensive and beautiful. Remy 38's were just as bad. Winchester 38 was ok tho. Only a couple would stick and 1 cylinder dropped completely with a hard smack. I had 5 beat up pmc bronze I saving as pocket ammo that I shot cuz it was looking ugly and the ejection dropped all but 1 or two. Stupid Taurus. Shoulda got a walther cuz Germans make good stuff and I'm a bond fan
-
May 26th, 2013, 03:40 PM #6Banned
- Join Date
- Jan 2009
- Location
-
S.W. Pa,
Pennsylvania
(Westmoreland County) - Posts
- 1,188
- Rep Power
- 0
-
May 26th, 2013, 03:45 PM #7Member
- Join Date
- May 2013
- Location
-
derry,
Pennsylvania
(Westmoreland County) - Posts
- 56
- Rep Power
- 870
Re: ejection problems
Lol I didn't have the money for anything other than a walther but I was attracted to the round and the fact that's a revolver
-
May 26th, 2013, 03:51 PM #8
-
May 26th, 2013, 04:13 PM #9Member
- Join Date
- May 2013
- Location
-
derry,
Pennsylvania
(Westmoreland County) - Posts
- 56
- Rep Power
- 870
Re: ejection problems
400 overal but the sticker was 350 and it was only fired 20 times
-
May 26th, 2013, 04:31 PM #10
Re: ejection problems
Some people just plain suck.
If you're gonna be dumb ya gotta be tough.
Similar Threads
-
AR-15 Ejection question
By maxxram in forum RiflesReplies: 16Last Post: March 12th, 2012, 12:08 AM -
M1 Garand ejection ?
By dodge in forum RiflesReplies: 4Last Post: September 14th, 2011, 12:15 AM -
LMT AR Ejection issues
By emsjeep in forum GeneralReplies: 20Last Post: August 25th, 2009, 01:41 PM -
Brass ejection problems- AR-15
By tec in forum GeneralReplies: 20Last Post: June 17th, 2008, 10:37 AM -
AR ejection direction
By Hawk in forum GeneralReplies: 10Last Post: February 15th, 2008, 08:38 PM
Bookmarks