Results 1 to 7 of 7
Thread: Question About Cleaning
-
March 19th, 2008, 12:11 AM #1
Question About Cleaning
I bought a stainless revolver used but in good shape other than the front of the cylinder has baked on powder residue. I mean...it is really on there and probably has been for quite some time..
What is the best and easiest way to remove this? I'm sure there is a cleaner for it, right?
-
March 19th, 2008, 12:13 AM #2
Re: Question About Cleaning
A powder solvent and elbow grease. A SS brush will help speed things up.
-
March 19th, 2008, 06:42 AM #3
Re: Question About Cleaning
Anyone, please correct me if I'm wrong, but what I have done on the used Model 85 I bought was to remove the cylinder and buff the face of it on a fine brass wire wheel.
Veritas Vos Liberat
-
March 19th, 2008, 11:57 PM #4Super Member
- Join Date
- Feb 2008
- Location
-
Bentleyville,
Pennsylvania
(Washington County) - Posts
- 595
- Rep Power
- 20
Re: Question About Cleaning
Hoppes #9 works wonders, as does CLP. Depending on the gun, that portion may never have been polished in the first place.
-
March 20th, 2008, 03:48 PM #5
Re: Question About Cleaning
Take the cylinder off the revolver and soak it in a jar of Hoppes #9 overnight.
Then use a stainless steel brush and brush it clean.
Bye for a while, guard the fort. - My Dad
-
March 20th, 2008, 06:19 PM #6Member
- Join Date
- Nov 2006
- Location
-
Carlisle,
Pennsylvania
(Cumberland County) - Posts
- 90
- Rep Power
- 18
Re: Question About Cleaning
The following procedure will clean a stainless steel revolver cylinder better than you would believe. It will look unfired. Do not do this to a blued cylinder with this solvent.
1) Get a bottle of a product called SLIP2000.
2) Find a container with an opening just big enough to put the revolver cylinder in it, put in the revolver cylinder, fill it with SLIP2000 till the cylinder is covered. Leave it there for about 3 days - 4 days if you have the time. The chemical does the work.
3) Remove the cylinder from the solvent, wipe the face of the cylinder clean with a soft cloth. No brushes required, the carbon will just wipe off.
4) Take a bronze bore brush for the next larger caliber and brush the chambers.
5) Run a couple of dry patches through each chamber.
6) Rinse in Hoppe's #9, wipe it down, patch the chambers dry, lube as required and reassemble to the revolver.
Trust me on this, the cylinder will be clean even if it had baked on carbon rings from shooting .38sp in a .357 chamber. SLIP2000 is the best carbon solvent I've ever used.
For blued cylinders soak in Hoppe's #9 for twice as long.
Fitch
-
March 25th, 2008, 12:32 AM #7
Re: Question About Cleaning
Thanks for all the help. I will try some of this and hopefully I will have a nice, shiny revolver when I'm done.
Similar Threads
-
A silly gun cleaning question
By melD in forum GeneralReplies: 10Last Post: October 8th, 2007, 12:12 PM -
Noob Question: Cleaning firearms
By BronzeDragon in forum GeneralReplies: 12Last Post: September 19th, 2007, 12:37 PM -
WTS: Cleaning out the closet
By Hawk in forum GeneralReplies: 1Last Post: September 8th, 2007, 09:02 AM -
AR Cleaning Kit?
By Lambo in forum GeneralReplies: 0Last Post: February 24th, 2007, 06:29 PM -
AR15 Cleaning
By greyhouse in forum GeneralReplies: 18Last Post: December 2nd, 2006, 09:09 PM
Bookmarks