Pennsylvania Firearm Owners Association

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.
Welcome to the Pennsylvania Firearm Owners Association Forum, we hope you like what you find here and we strongly encourage you to register for an account with us, especially if you are from Pennsylvania. Once registered you will have access to participate in our community. Thanks for visiting and we hope you become a regular!
Attention! There has been an influx of scammer signups!

The method of operation is to private message you and tell you that you should contact such 'n such person at a given email address.

Please report the private messages. Staff will ban the offender, and I will implement an IP ban. Unfortunately these scammers are using VPN/proxy services, which may mean your VPN/proxy may be blocked.
Attention! About VPN's and foreign IP addresses.

When signing up, do so from a US based Internet Service Provider. Turn off any VPN/safe-browsing feature. Failure to do so will result with your new account denied.

If you run into a IP ban afterwards as a member, again - turn off your VPN or switch servers. We do not ban legit Internet Service Providers from the USA(exception for certain individual IP addresses). Free VPN's tend to get banned too. We try not to ban legit subscription VPN services, but they rarely label their IP blocks correctly.

If you run into an IP ban, it likely wasn't you.

Results 1 to 2 of 2

Thread: Engraving.

Thread Tools
Display
- Linear Mode
- Switch to Hybrid Mode
- Switch to Threaded Mode

February 20th, 2012, 12:49 PM #1
SCBaldr

View Profile

View Forum Posts

Private Message

Super Member
Join Date

Jun 2010

Location

Helena, Montana

Posts

977

Rep Power

217721
Engraving.

Does anyone know of a good engraver who can engrave the slide of a pistol with text so that I can later fill the engraving with Cerakote and thereby colorize the text? Local is good, but quality is better.

The M1. Smackin' the bastards since 1932.

Reply With Quote
February 20th, 2012, 10:09 PM #2
mioduz

View Profile

View Forum Posts

Private Message

Member
Join Date

May 2007

Location

Erie, Pennsylvania
(Erie County)

Posts

67

Rep Power

372
Re: Engraving.

I am located in Erie and can take care of that if you want to ship the slide. Email me at chrismio@hotmail.com if interested. Please include font size what you want engraved etc etc

Reply With Quote

Quick Navigation Gunsmithing Top

Site Areas
Settings
Private Messages
Subscriptions
Who's Online
Search Forums
Forums Home
Forums
Forum
Discussion
Law & Politics
1. Pennsylvania
2. National
Marketplace
Events
Private Forums
1. PAFOA Club
Regions
1. Lake Erie Region
  1. Crawford
  2. Erie
  3. Mercer
  4. Venango
2. Allegheny National Forest Region
  1. Cameron
  2. Clarion
  3. Clearfield
  4. Elk
  5. Forest
  6. Jefferson
  7. McKean
  8. Potter
  9. Tioga
  10. Warren
3. Valleys of the Susquehanna Region
  1. Centre
  2. Clinton
  3. Columbia
  4. Juniata
  5. Lycoming
  6. Mifflin
  7. Montour
  8. Northumberland
  9. Snyder
  10. Union
4. Pocono Mountain Region
  1. Bradford
  2. Carbon
  3. Lackawanna
  4. Luzerne
  5. Monroe
  6. Pike
  7. Schuylkill
  8. Sullivan
  9. Susquehanna
  10. Wayne
  11. Wyoming
5. Lehigh Valley & Philadelphia Region
  1. Bucks
  2. Chester
  3. Delaware
  4. Lehigh
  5. Montgomery
  6. Northampton
  7. Philadelphia
6. PA Dutch Country/Hershey Region
  1. Adams
  2. Berks
  3. Cumberland
  4. Dauphin
  5. Franklin
  6. Lancaster
  7. Lebanon
  8. Perry
  9. York
7. Laurel Highlands Region
  1. Bedford
  2. Blair
  3. Cambria
  4. Fayette
  5. Fulton
  6. Greene
  7. Huntingdon
  8. Indiana
  9. Somerset
  10. Westmoreland
8. Pittsburgh Region
  1. Allegheny
  2. Armstrong
  3. Beaver
  4. Butler
  5. Lawrence
  6. Washington
Miscellaneous
1. The Lounge

« Previous Thread | Next Thread »

Similar Threads

Engraving a gun

By glocking26 in forum NFA/Class 3/Title II

Replies: 6
Last Post: July 8th, 2010, 02:36 PM
Engraving -- Who and How much?

By pa123guns in forum NFA/Class 3/Title II

Replies: 18
Last Post: March 30th, 2010, 09:09 PM
Engraving

By NikeBauer21 in forum General

Replies: 4
Last Post: September 24th, 2009, 07:09 PM
Engraving

By mojo in forum General

Replies: 2
Last Post: April 15th, 2009, 09:13 AM
NFA engraving

By cruzie27 in forum General

Replies: 6
Last Post: November 8th, 2007, 06:56 PM