Results 1 to 10 of 12
Thread: Springfield 1911 question
-
January 26th, 2008, 12:03 AM #1
Springfield 1911 question
I have a loaded Springfield 1911 45 acp, I just purchased some Wilson 47D 8-round magazines. When inserting the Wilson mags they slide in fine until they hit the latching mechanism and they won't go any further unless you bump them hard or hold in the release button.Is this normal?the gun works fine with the stock Springfield mags.
ThanksSteve
-
January 26th, 2008, 12:09 AM #2
Re: Springfield 1911 question
Does this happen with the slide locked back? Does this happen if you strip a round or two off?
_____________________________________________
I won't be wronged. I won't be insulted. I won't be laid-a-hand on.
I don't do these things to other people, and I require the same from them. - John Wayne - The Shootist
Many of the truths we cling to... depend greatly on our own point of view. - Obi-Wan Kenobi
-
January 26th, 2008, 09:58 AM #3
Re: Springfield 1911 question
It happens if the magazine is full or empty and also happens when the slide is locked back and closed
Steve
-
January 27th, 2008, 04:00 PM #4
Re: Springfield 1911 question
Any other ideas?
Steve
-
January 27th, 2008, 04:06 PM #5
Re: Springfield 1911 question
I would have to say stay with the Springfield mags in that case.
-
January 27th, 2008, 05:34 PM #6
Re: Springfield 1911 question
Remove the slide from the gun, install the slide stop, and insert that magazine loaded. Note whether or not the bullet touches any part of the slide stop (it should just barely clear it).
Unload the magazine and re-insert. Note where the follower of the empty magazine pushes up on the slide stop and compare it to a known good one._____________________________________________
I won't be wronged. I won't be insulted. I won't be laid-a-hand on.
I don't do these things to other people, and I require the same from them. - John Wayne - The Shootist
Many of the truths we cling to... depend greatly on our own point of view. - Obi-Wan Kenobi
-
January 27th, 2008, 06:33 PM #7
Re: Springfield 1911 question
I have the same thing with my Springfield loaded. I spoke to Springfield and they told me the Wilson mags are some times a bit tight untill they wear in.
The truth shall set you free.
They can have my guns when they pry them from my cold dead hands
I can not wait until NJ sinks in the ocean and PA has ocean front property
-
March 13th, 2008, 08:38 AM #8
Re: Springfield 1911 question
Try the 7 rounders...i have a TRP and the 8 rounders fit but are tight...7 rounders are great!!!
MOLON LABE
-
March 17th, 2008, 05:50 PM #9
Re: Springfield 1911 question
The mag catch spring probably just needs a little breaking in. I use 47DAB's ( 8rd, .350 bases, black) in my TRP and they work quite well.
Machinist for hire - Get a hold of me if you need something made
-
March 17th, 2008, 06:07 PM #10
Re: Springfield 1911 question
All of my Springfield Armory 1911's (3) did this with Wilson, Tripp, CMI and Metalform magazines until the gun was broken in some. One of them still does it.
Similar Threads
-
Springfield Mil-Spec 1911
By WWGunslinger in forum GeneralReplies: 5Last Post: January 18th, 2008, 11:31 PM -
Springfield GI-45 1911
By JustinM in forum GeneralReplies: 33Last Post: January 17th, 2008, 12:20 PM -
WTB: Springfield 1911 Grips
By Kypt in forum GeneralReplies: 0Last Post: October 23rd, 2007, 10:26 AM -
WTS: (PA) NIB - Springfield Armory .45acp 1911-A1
By nra-life-member in forum GeneralReplies: 0Last Post: April 23rd, 2007, 12:50 AM -
Recommendation for Springfield 1911
By luckyned7 in forum GeneralReplies: 2Last Post: October 21st, 2006, 08:44 PM
Bookmarks