Results 1 to 10 of 14
Thread: Mosin 91/30 Help
-
September 13th, 2011, 11:55 PM #1
Mosin 91/30 Help
Okay so at the Pittsburgh Mills gun show I couldn't restrain myself and bought a Mosin Nagant, now I took it home cleaned out the cosmoline, took a 20 gauge bore brush to the chamber with a drill.
The problem is that when I go to chamber a round the bolt will not close on some rounds. I know it's not head space because even the hardest to chamber rounds let the bolt open and close easily after the extractor grabs on to them. I've taken the extractor out twice and tried to polish it with a fine sharpening stone. Please help , and thanks in advance. I've tried 2 days to fix this and decide that I need the insightful help of PAFOA.
-
September 14th, 2011, 12:09 AM #2
Re: Mosin 91/30 Help
So the extractor isnt grabbing on the rim properly?
Do you have it assembled correctly? Is this under a full magazine, or are you feeding them in by hand? Ive had trouble feeding 1 by 1 in the same way.
-
September 14th, 2011, 12:12 AM #3
Re: Mosin 91/30 Help
The extractor is not latching onto the rim correctly, there is no difference loading wise, full mag or one by one. The bolt will go all the way forward and stop/get stuck around 45°-60°. As stated after the bolt goes down (hence the extractor latches onto the rim) I can open and close it like butter.
-
September 14th, 2011, 01:31 AM #4Super Member
- Join Date
- Sep 2010
- Location
-
SW,
Pennsylvania
(Beaver County) - Posts
- 793
- Rep Power
- 3531827
Re: Mosin 91/30 Help
You have a PM in your inbox
-
September 14th, 2011, 08:21 AM #5Banned
- Join Date
- Feb 2010
- Location
-
Upper Macungie,
Pennsylvania
(Lehigh County) - Age
- 62
- Posts
- 1,158
- Rep Power
- 0
Re: Mosin 91/30 Help
try reading this, might help
-
September 14th, 2011, 10:20 AM #6
Re: Mosin 91/30 Help
I already ran a bore brush in the chamber, and it isn't sticky bolt because I haven't fired it yet. It's just very hard when initially closing the bolt to get the extractor to snap over the round.
-
September 14th, 2011, 10:35 AM #7Banned
- Join Date
- Feb 2010
- Location
-
Upper Macungie,
Pennsylvania
(Lehigh County) - Age
- 62
- Posts
- 1,158
- Rep Power
- 0
Re: Mosin 91/30 Help
take the bolt apart and clean it again. cosmo can get everywhere. i cleaned mine, bolt, chamber, everything i could 2 or 3 times to get that stuff out. finally loads and shoots perfectly now.
-
September 14th, 2011, 10:56 AM #8
Re: Mosin 91/30 Help
yeah, you could have cosmo under the extractor. I use a bath of brake cleaner followed by steam cleaning (get er' hot) to get it all out without having to take out puns and springs.
-
September 14th, 2011, 02:46 PM #9
Re: Mosin 91/30 Help
I've taken the extractor out 3 times and as of now I'm calling this fixed. There was an indent in the extractor from a rim embedding into it, don't know how it happened, but I polished it with a fine sharpening stone until the dent was gone now it's much smoother, thanks for everyone's help
-
September 14th, 2011, 11:06 PM #10
Similar Threads
-
My first Mosin
By t1m0thy in forum Gun PicturesReplies: 10Last Post: April 21st, 2011, 05:57 PM -
Scoped Mosin/Scout Mosin/Sporterized Mosin
By Kb! Bob in forum GeneralReplies: 0Last Post: December 21st, 2009, 08:57 PM -
Mosin M39, Mosin M38, Mosin M91 P-27, M1 carbine and Geha shotgun
By wizzegun in forum GeneralReplies: 1Last Post: May 21st, 2009, 10:29 PM -
WTB: mosin 91/30
By toadyoforangeville in forum GeneralReplies: 1Last Post: February 27th, 2008, 02:30 AM
Bookmarks