Results 1 to 10 of 15
Thread: AR-15 weapon lock question
-
December 28th, 2007, 06:25 PM #1Member
- Join Date
- Oct 2007
- Location
-
West Chester,
Pennsylvania
(Chester County) - Posts
- 92
- Rep Power
- 17
AR-15 weapon lock question
Hi guys, I was wondering- is it OK for the rifle/carbine if the bolt is locked in the backward position for periods of time, say a few days or weeks? Thanks.
"We must all hang together, or, most assuredly, we shall all hang separately." -Benjamin Franklin
M91/30 ~ Stag 15 Model 2
-
December 28th, 2007, 06:30 PM #2
Re: AR-15 weapon lock question
Good question! I am watching this thread because I have my bolt locked open for quick readiness when needed...but if it is bad on the recoil spring I will release it.
New AR15 Forum! www.AlphaRomeo15.org All AR, No Attitude!
-
December 28th, 2007, 06:45 PM #3
Re: AR-15 weapon lock question
I would assume ( you know what that gets us...) that a recoil spring would be the same as a magazine spring. They don't lose strength from being held compressed. They lose strength from cycling. So, I would say there would be no harm in keeping you bolt locked back. But, take that advice at your own risk as I'm not an expert, and I definitely didn't stay at a holiday inn last night.
-
December 28th, 2007, 08:34 PM #4Grand Member
- Join Date
- Aug 2006
- Location
-
Nowhere Land,
Pennsylvania
(Westmoreland County) - Posts
- 4,954
- Rep Power
- 5723755
-
December 28th, 2007, 08:35 PM #5
-
December 28th, 2007, 08:47 PM #6Grand Member
- Join Date
- Aug 2006
- Location
-
Nowhere Land,
Pennsylvania
(Westmoreland County) - Posts
- 4,954
- Rep Power
- 5723755
Re: AR-15 weapon lock question
Actually, I think it's a bad idea to keep your carbine in "cruiser ready" condition.
Chambering a round when something goes "bump in the night" when you may be dreary eyed and having just awoken from a deep sleep is not a good time to rely on a round being chambered. Not only that, chambering a round is quite noisy and performing a crossover status check with "sleep" in your eyes is not conducive to the process.
I want my carbine locked and loaded BEFORE I need it.
-
December 28th, 2007, 08:59 PM #7Member
- Join Date
- Oct 2007
- Location
-
West Chester,
Pennsylvania
(Chester County) - Posts
- 92
- Rep Power
- 17
Re: AR-15 weapon lock question
Ah OK cool, thanks everyone. I don't want to hurt my new baby.
"We must all hang together, or, most assuredly, we shall all hang separately." -Benjamin Franklin
M91/30 ~ Stag 15 Model 2
-
December 28th, 2007, 09:05 PM #8
Re: AR-15 weapon lock question
u have a great point there Tony infact i believe if you chamber a round inside a dwelling you should use the chargeing handle and let the bolt move forward slowly and then use the froward asst. to verify the bolt is locked completely froward, also a quiet way to load a AR
letting the bolt go from the bolt release may cause a slam fire
cause of the non captive firing pin.
u can see this if you load the chamber by rackin it with CH or release from the bolt release, clear the weapon and look at the unfired round youll notice a small firing pin mark
-
December 28th, 2007, 09:37 PM #9
Re: AR-15 weapon lock question
"Oderint Dum Metuant" - BMFH
"Tact is for people not witty enough to use sarcasm"
Note: any whingeing crazy that hits my PM inbox will be deleted without reply
-
December 28th, 2007, 09:41 PM #10
Re: AR-15 weapon lock question
(I feel like I'm splittin hairs here) My Russian SKS does indeed have a spring loaded firing pin, so no slam fires here. But you are correct for the rest.
(On topic)
Every firearm that I use for home defense is ready to go. Flick off the safety and rock and roll. As Tony said, there is no sense adding one more (noisy) step to your routine when a locked and loaded firearm is just as safe.
Similar Threads
-
Used NIB condition S&W 442 pre lock
By TonyF in forum GeneralReplies: 2Last Post: November 8th, 2007, 07:57 PM -
anyone used LOCK'S gunsmithing?
By smoke-wagon in forum GeneralReplies: 2Last Post: October 23rd, 2007, 06:28 AM -
???? for Lock N Load Owners
By 1927A1 in forum GeneralReplies: 2Last Post: August 3rd, 2007, 10:27 PM -
Lock N Load Presses
By 1927A1 in forum GeneralReplies: 6Last Post: July 12th, 2007, 11:23 PM -
Hornady Lock N Load AP
By aubie515 in forum GeneralReplies: 5Last Post: September 25th, 2006, 04:45 PM
Bookmarks