Results 1 to 9 of 9
Thread: BUILD FROM PARTS KIT
-
November 29th, 2007, 04:33 PM #1
BUILD FROM PARTS KIT
i would like to build a parts kit gun (ak) is there anything that i have to do besides use ten u.s. parts?
-
November 29th, 2007, 05:29 PM #2
Re: BUILD FROM PARTS KIT
you mean legaly??
no, and you dont need 10 us parts, you just cant use more than 10 foreign parts.
that usually = 6 us parts
-
November 29th, 2007, 05:51 PM #3
-
November 30th, 2007, 11:09 PM #4
Re: BUILD FROM PARTS KIT
a us receiver will be one part. a fcg is usually recomended, thats 3 more.
that leaves 2 more pars to change.
most popular are pistolgrips, buttstocks, gas pistons, muzzle devices, and front handguards.
-
November 30th, 2007, 11:55 PM #5
-
December 1st, 2007, 02:09 AM #6Grand Member
- Join Date
- Sep 2007
- Location
-
Effort,
Pennsylvania
(Monroe County) - Posts
- 2,262
- Rep Power
- 3681644
Re: BUILD FROM PARTS KIT
"how the hell can they know if the parts are foreign or domestic?"
You hit the nail on the head! Up until very recently, none of the U.S. made parts were marked "Made in The U.S. so there was no way to prove that they were U.S. made!
-
December 1st, 2007, 03:28 AM #7
Re: BUILD FROM PARTS KIT
There are some good US trigger groups that'll add 3 pieces to the component list. Trigger, hammer and disconnector. I personally prefer the double hook group.
US gas piston can be had, but if your bolt carrier already as a foreign piston - its a bitch to change out. ... a real bitch.
Go with a US receiver, (3) piece trigger group, butt stock, grip and forearm handguard(7 parts total). If you plan to get a crap load of magazines - it wouldn't be worth it to buy floor plates and followers for all of them - better to use mil-surp mags for cheap savings and it wont matter what make of mag you pickup to use..
-
December 1st, 2007, 10:59 AM #8
-
December 1st, 2007, 01:10 PM #9
Re: BUILD FROM PARTS KIT
No.
There are about only 20 parts that the BATF considers a "firearm part". Of the 20 or so, only 16 are within a AK platform if its a stamped receiver. 15 if its a milled receiver.
1. receiver
2. barrel
3. muzzle attachment
4. gas piston
5. trunnion (part into which barrel is inserted, only on stamped guns)
6. bolt
7. bolt carrier
8. hammer
9. disconnector
10. trigger
11. buttstock
12. pistol grip
13. handguard set (counts as one even though two parts)
14. magazine body
15. magazine follower
16. magazine floorplate.
Of the 16 parts above on a stamped receiver - you have to have no more than 10 foreign made parts. That means you must have 6 US made parts. With milled receivers - the trunnion is actually part of the receiver. ..not a part that is riveted in.
Similar Threads
-
Help me build an AR
By Spectre6 in forum GeneralReplies: 32Last Post: June 5th, 2008, 10:55 AM -
ar15 build parts?
By BFit70 in forum GeneralReplies: 20Last Post: March 17th, 2008, 08:12 PM -
fal build
By KCZeppelin in forum GeneralReplies: 7Last Post: May 4th, 2007, 11:04 AM -
New Computer Build
By phillyd2 in forum GeneralReplies: 19Last Post: April 3rd, 2007, 09:28 AM -
My New AR-15 build...
By JayBell in forum RiflesReplies: 8Last Post: December 26th, 2006, 11:58 PM
Bookmarks