Results 1 to 10 of 23
-
February 8th, 2007, 02:23 PM #1Banned
- Join Date
- Oct 2006
- Location
-
STFU, staff
(Beaver County) - Posts
- 295
- Rep Power
- 0
Smith Wanted: pivot pin detent hole drill
I have someone local to do the barrel threading on my AR.
Now I need someone else to drill the hole into the reciever needed for the pivot pin detent, and the detent spring. Its an inch long 3/32" hole into the "Fence" on the magazine well.
I have the parts needed for the job, I only need the service of drilling the hole.
If you can do this, and will not require a FFL for shipping (not required if within PA) let me know how much you are asking for, and a turn around time.
If I cant find anyone to do it, I'll be attempting it myself.
Thanks!
-
February 8th, 2007, 06:04 PM #2Grand Member
- Join Date
- Aug 2006
- Location
-
Nowhere Land,
Pennsylvania
(Westmoreland County) - Posts
- 4,954
- Rep Power
- 5938504
-
February 8th, 2007, 06:08 PM #3Banned
- Join Date
- Oct 2006
- Location
-
STFU, staff
(Beaver County) - Posts
- 295
- Rep Power
- 0
Re: Smith Wanted: pivot pin detent hole drill
Thank you
I'm not sure. It kinda broke my heart when I brought the AR home for the first time, and my room-mate (ex-mil) grabed it and began his tear-down sequence. He got stuck when he realized he needed a screw driver. It just did not compute for him.
So-I want to make it so that there are no (well, as few as possible) tools to disassemble it.
Do you suggest that I not *militarize* it?
-
February 8th, 2007, 06:17 PM #4Grand Member
- Join Date
- Aug 2006
- Location
-
Nowhere Land,
Pennsylvania
(Westmoreland County) - Posts
- 4,954
- Rep Power
- 5938504
Re: Smith Wanted: pivot pin detent hole drill
-
February 8th, 2007, 06:24 PM #5Banned
- Join Date
- Oct 2006
- Location
-
STFU, staff
(Beaver County) - Posts
- 295
- Rep Power
- 0
Re: Smith Wanted: pivot pin detent hole drill
I think it'd just be something different and nice. I'm pretty confident that I can handle doing it myself. I have access to a mill, and I would "practice" a few times on an Al block.
That is unless someone can do it for me-but thats not looking likelyLast edited by avizpls; February 8th, 2007 at 10:20 PM.
-
February 8th, 2007, 09:45 PM #6
Re: Smith Wanted: pivot pin detent hole drill
err...its not 'militarizing" the lower, lets say "standardizing"
the standard is front and rear pushpins for everybody BUT colt.
Colts are the only maker around that have messed with the design to such an extent as to make it difficult to field strip the gun, not to mention get replacement parts for the FCG.
I can't suggest a local gunsmith for him, I dont know his area.
frankly, with the tools i have I dont know if i'd try this myself, even tho i have a drill press.
it's a simple procedure if you have the press, and clamps, and such."Oderint Dum Metuant" - BMFH
"Tact is for people not witty enough to use sarcasm"
Note: any whingeing crazy that hits my PM inbox will be deleted without reply
-
February 8th, 2007, 10:05 PM #7Banned
- Join Date
- Oct 2006
- Location
-
STFU, staff
(Beaver County) - Posts
- 295
- Rep Power
- 0
Re: Smith Wanted: pivot pin detent hole drill
the standard is front and rear pushpins for everybody BUT colt.
I decided I'm doing it myself. I've got the receiver stripped. I will make a 2x4 clamp for it tomorrow. Then I just have to wait for the pins to come in on monday. Wednesday, I'll report back on how the drilling went. Or maybe I'll post a "WTB: Colt lower" threadLast edited by avizpls; February 8th, 2007 at 10:21 PM.
-
February 8th, 2007, 10:28 PM #8
Re: Smith Wanted: pivot pin detent hole drill
Stripped Stag lowers run $90.........
Go for it!
-
February 8th, 2007, 11:36 PM #9Banned
- Join Date
- Oct 2006
- Location
-
STFU, staff
(Beaver County) - Posts
- 295
- Rep Power
- 0
Re: Smith Wanted: pivot pin detent hole drill
...but I have a colt, and I want to keep it that way.
The worst part is this: suppose I shoot a drill bit out the side of my magazine well. I'll do whatever it takes, and spend however much I need to to get another Colt lower.
Then I'll try again.
-
February 8th, 2007, 11:51 PM #10
Re: Smith Wanted: pivot pin detent hole drill
But.....CMT makes both Stag and Colt lowers.......so it would still be the same....save for the rollmark and the extra $200.
Similar Threads
-
WTT CZ 75B for Smith M&P Compact 9
By sig-9 in forum GeneralReplies: 4Last Post: January 28th, 2007, 08:56 PM -
WTB smith M&P compact 9mm
By sig-9 in forum GeneralReplies: 0Last Post: January 27th, 2007, 07:02 PM -
Wanted - Smith 686 3 inch Custom Officer
By sig-9 in forum GeneralReplies: 0Last Post: December 29th, 2006, 07:43 AM -
smith and wesson 340 pd
By rgb03 in forum GeneralReplies: 5Last Post: December 21st, 2006, 02:01 PM -
Looking for Garand 'smith
By 762xIan in forum GeneralReplies: 12Last Post: March 30th, 2006, 04:07 PM
Bookmarks