Results 1 to 10 of 13
Thread: Nickel vs Brass case HeLp
-
January 26th, 2007, 05:34 PM #1Member
- Join Date
- Dec 2006
- Location
-
N/A,
Idaho
- Posts
- 44
- Rep Power
- 0
Nickel vs Brass case HeLp
Is one better then the other? I am looking to buy some cases for my 300 WBY and am debating on whether or not buying Nickel or Brass. Also, does anyone know if Remington brass is a good as factory WBY brass?
Thanks!
-
January 26th, 2007, 06:44 PM #2Grand Member
- Join Date
- Aug 2006
- Location
-
Nowhere Land,
Pennsylvania
(Westmoreland County) - Posts
- 4,954
- Rep Power
- 5938504
Re: Nickel vs Brass case HeLp
Nickel resists corrosion but if the case becomes scratched my understanding is there is potential to scratch reloading dies.
-
January 26th, 2007, 09:10 PM #3
Re: Nickel vs Brass case HeLp
Nickel is going to cost you a lot more for the brass. I just don't see the benefits to justify buying nickel brass. When I find it at the range, I'll pick it up, but I'm not going to waste more money on it. I am not a fan of Remington or Federal brass. I like Winchester and Hornady brass for domestic. Lapua and Norma brass are considered the best overall brass in the markt.
-
January 27th, 2007, 08:56 PM #4Super Member
- Join Date
- Sep 2006
- Location
-
Pennsylvania
(Schuylkill County) - Posts
- 528
- Rep Power
- 226719
Re: Nickel vs Brass case HeLp
Straight walled pistol sizing dies are generally CARBIDE. No scratching unless you cheap out and get the steel dies that need lubing.
Nickel plated brass will tolerate much more pressure. Some say it wears out quicker but I Have not seen any issues with the 1500 pieces I used for .357Mag.
Some also say the nickel will chip off. Again, not seen it.
I like nickel for several reasons:
Easy to tell my .357 from .38 cases (one is nickel, the other is not)
Nickel seems to repel dirt. I rarely tumble for more than 10 min to get clean nickel brass.
Less force to resize (I have notices the nickel feels 'slicker' when I resize).
Will not tarnish.
Generally I would, for even a modest price difference, go for nickel over brass for .357.
-
January 28th, 2007, 01:50 AM #5Grand Member
- Join Date
- Aug 2006
- Location
-
Nowhere Land,
Pennsylvania
(Westmoreland County) - Posts
- 4,954
- Rep Power
- 5938504
-
January 28th, 2007, 03:06 PM #6
Re: Nickel vs Brass case HeLp
There was a similar thread on GlockTalk a couple months ago.
General reports were that the nickel cases crack more often than plain brass, at least in the higher pressure rounds. I've got a few pieces of cracked nickel "FC" 9mm brass that had only been loaded twice. I've got some nickel Federal 45ACP brass that I've loaded 6 times now, and it's fine.
-
January 28th, 2007, 09:46 PM #7Senior Member
- Join Date
- Nov 2006
- Location
-
West Chester,
Pennsylvania
(Chester County) - Posts
- 290
- Rep Power
- 557
Re: Nickel vs Brass case HeLp
Brass cases are easier to size, and less likely to crack. Unless the nickel is free or really cheaper, i'd go with the brass cases
-
February 1st, 2007, 12:49 AM #8Super Member
- Join Date
- Sep 2006
- Location
-
Pennsylvania
(Schuylkill County) - Posts
- 528
- Rep Power
- 226719
Re: Nickel vs Brass case HeLp
I hardly feel any 'resizing' of .357 brass. If you blind fold yourself and randomly pick from a bin of nickel and brass fired cases (from the same gun) you'll be able to tell the nickel from the brass. Brass need more force to resize and has more friction on the die. Nickel feels lubed (well, cause it is, by the nickel)
-
February 3rd, 2007, 07:20 PM #9Member
- Join Date
- Dec 2006
- Location
-
N/A,
Idaho
- Posts
- 44
- Rep Power
- 0
Re: Nickel vs Brass case HeLp
Looks like weatherby brass is made by Norma.
http://www.midwayusa.com/eproductpag...eitemid=557377
Weatherby Brass 300 Weatherby Magnum Box of 20
Produced exclusively for Weatherby by Norma Precision. Brass has CNC-machined primer pockets and is made to match-grade specifications. New unprimed brass. This is not loaded ammunition.
I will stick with buying once fired weatherby brass off of eBay.
-
February 4th, 2007, 06:46 PM #10Super Member
- Join Date
- Sep 2006
- Location
-
Pennsylvania
(Schuylkill County) - Posts
- 528
- Rep Power
- 226719
Re: Nickel vs Brass case HeLp
For expensive brass like the 300Wby you should look into annealing setups to make the brass last dozens of reloads.
There is an excellent annealing system availalbe for like $300 Runs off propane.
SInce $300 is not really that much brass for that particular cartridge, I would do all I could to make it last.
Not to 'diss' e-bay brass.. but ever notice that EVERY e-bay auction is for ONCE FIRED brass? Even range pickups?
Similar Threads
-
2nd Amendment case being heard now
By LittleRedToyota in forum GeneralReplies: 19Last Post: January 27th, 2007, 03:00 PM -
Wanted: AR15 case
By avizpls in forum GeneralReplies: 7Last Post: December 2nd, 2006, 08:08 PM
Bookmarks