Results 1 to 8 of 8
-
November 11th, 2019, 02:35 PM #1
Need a little help. Federal .556 55gr corrosion?
I have around 1000 rounds of Federal .556 and its been stored in a metal military ammo box for some time. Inside these paper boxes.
Federal.jpg
I recently decided to go shoot a little and took a couple boxes out to rotate the ammunition and discovered this.
Federal wtf.jpg
I'm now moving all the ammo into these plastic boxes to try and prevent this from continuing.
Federal 1.jpg
Is this caused by the ammo just aging and not being used, moisture related or low quality loading. Are the remaining rounds safe? I plan to remove the bullets from the bad rounds and dump the powder to dispose of them.
-
November 11th, 2019, 03:52 PM #2
Re: Need a little help. Federal .556 55gr corrosion?
They were stored improperly at some point of their life, exposed to too much moisture.
I'm a little fuzzy on Federal LOT numbers. They changed the numbering system several times over the past 50 years. I think that LOT number indicates pre-1974???Last edited by Hawk; November 11th, 2019 at 04:13 PM.
Toujours prêt
-
November 11th, 2019, 04:08 PM #3Grand Member
- Join Date
- Jan 2013
- Location
-
Richboro,
Pennsylvania
(Bucks County) - Posts
- 3,173
- Rep Power
- 21474851
Re: Need a little help. Federal .556 55gr corrosion?
Kind of strange the boxes look perfect with no signs of water.
I would not shoot the top two rounds. The top one is too far gone and the middle one has corrosion on the neck and bullet. I would be tempted to just hit the bottom one with some steel wool to get rid of the one spot of corrosion (but thats just me).
So now the fun part. Will the primers still work.
-
November 11th, 2019, 04:29 PM #4Grand Member
- Join Date
- Aug 2010
- Location
-
South East of disorder
- Posts
- 3,626
- Rep Power
- 21474854
Re: Need a little help. Federal .556 55gr corrosion?
I agree at some point they were exposed to moisture.
Aggies Coach Really ??? Take off the tin foil bro.
-
November 11th, 2019, 04:32 PM #5
Re: Need a little help. Federal .556 55gr corrosion?
The cardboard cartons got damp; not soaking wet, but full of humidity damp. That kind of cardboard is made from unbleached or lightly bleached wood pulp in a process that is naturally acidic. The "wet end" of the board machine is probably running at a pH between 4.0 and 4.5. The dried board product (an ammunition box, in this case) still has acidic papermaking residues, and if the carton gets damp (or soaking wet), the acidic residue can attack (corrode) metals and metal alloys that are "active" on the electrochemical series, e.g., magnesium, aluminum, zinc, copper, iron/steel, etc.
There was a bit of German and Austrian 7.62 NATO ammo that was imported like 15-20 yrs ago that exhibited such corrosion, and when a box was carefully opened and the ammo and the box sides were examined, the ammo exhibited corrosion where it contacted the box, and the box and divider sides were "stained" directly opposite where a given round of ammunition had made contact with the box or divider. In the case of the German ammo (DAG if I recall correctly) and the Austrian Hirtenberger ammo, the same characteristics of corroded ammo and packaging stains were present.
In your case, the problem might be isolated to certain individual 20 rd cartons that got more damp than others. Or, it could be the paperboard process ran more acidic (4.0 vs. 4.5 or 5.0 even) when the packaging for your ammo was made. In any event, it has nothing to do with the ammo manufacturing process, and everything to do with packaging and environmental conditions.
If you have a quantity of empty magazines, just sort out the corroded ammo, fill the mags with the good stuff, and store the mags. The springs won't be affected if they are stored filled. The springs may take a bit of a "set", but that is taken into account by the spring designer and won't affect mag performance, if they are quality mags to begin with.
HTH,
NoahWisdom and knowledge shall be the stability of thy times.
-
November 11th, 2019, 05:16 PM #6
Re: Need a little help. Federal .556 55gr corrosion?
Gotta love having Encyclopedia Noah for reference. Hokey smokes!
Diversity is the greatest weakness, excellence is the greatest strength. JPC
-
November 11th, 2019, 05:37 PM #7
Re: Need a little help. Federal .556 55gr corrosion?
I have ammo the Navy gave me over 10 years ago and it's in the STD mil cardboard boxes, in a can with descant and looks as it should- prefect.
Owner Trigger Time LLc 01 FFL/NFA Saylorsburg, PA. Sales/Service/Transfers/Training
NRA CRSO/Pistol/Rifle/Shotgun inst. BSA Rifle/Shotgun Merit badge counselor. US Navy Marksmanship Team Staff
-
November 11th, 2019, 05:45 PM #8
Re: Need a little help. Federal .556 55gr corrosion?
I don't speak English , I talk American!
Similar Threads
-
Federal 55GR .223 for LC M855
By Whiskey1 in forum GeneralReplies: 0Last Post: August 13th, 2009, 05:51 PM -
Federal 55gr. fmj 223
By sig22940 in forum GeneralReplies: 0Last Post: March 10th, 2009, 08:21 AM
Bookmarks