Results 1 to 7 of 7
Thread: Mech Tec 1911 Conversion Kit
-
February 27th, 2008, 11:20 AM #1Senior Member
- Join Date
- Jan 2007
- Location
-
Pittsburgh,
Pennsylvania
(Allegheny County) - Age
- 55
- Posts
- 332
- Rep Power
- 118
Mech Tec 1911 Conversion Kit
I was thinking of getting one of the Mech Tec 1911 Carbine conversion kits and I wondered if any of you have tried one? I'm not a big fan of the stock on them but otherwise I think it would be kind of fun to play with. Any thoughts?
-
February 27th, 2008, 06:25 PM #2
Re: Mech Tec 1911 Conversion Kit
Had one in .38 Super, great shooter just could not stand the stock. When you are done with it they are hard to sell.
Courage is being scared to death--but saddling up any way. John Wayne
-
February 28th, 2008, 11:36 AM #3Senior Member
- Join Date
- Jan 2007
- Location
-
Pittsburgh,
Pennsylvania
(Allegheny County) - Age
- 55
- Posts
- 332
- Rep Power
- 118
Re: Mech Tec 1911 Conversion Kit
good point on trying to sell one. i'll have to make sure i kick gunbroker and gunsamerica around and look for a deal.
-
February 28th, 2008, 12:05 PM #4
Re: Mech Tec 1911 Conversion Kit
You have to do permanent modification to the gun to install them?
Audemus jura nostra defendere
-
February 28th, 2008, 05:28 PM #5Senior Member
- Join Date
- Jan 2007
- Location
-
Pittsburgh,
Pennsylvania
(Allegheny County) - Age
- 55
- Posts
- 332
- Rep Power
- 118
Re: Mech Tec 1911 Conversion Kit
No, you just take off the slide from the existing full size 1911 and they attach without modification or gunsmithing. i wonder if one would fit on my springfield champion since it only has a 4 inch barrel.
also, other than the stock being ugly, what didn't you like?
-
February 28th, 2008, 07:07 PM #6
Re: Mech Tec 1911 Conversion Kit
It was not the appearance, the stock was very uncomfortable. I sold the extra 1911 that was dedicated to the upper. On the positive side with .38 Super heavy loads and a scope it would scare you with the groups at 100 yds. My rifle shooter friend shot a 1.75 inch 3 shot group, my best was about 2.5 in.
Courage is being scared to death--but saddling up any way. John Wayne
-
November 17th, 2008, 10:26 AM #7Junior Member
- Join Date
- Nov 2008
- Location
-
Austin
- Posts
- 1
- Rep Power
- 0
Re: Mech Tec 1911 Conversion Kit
The mech tec for the glock 21 is a great tool. 30 round magazines are plentiful. If you go to their website, they have 3 stock options. A little imagination, purchase a SBR permit and cut down the barrel, add a silencer... it could be a great survival gun.
Similar Threads
-
.30-30 to .25-35 conversion
By Montell C. Williams in forum GeneralReplies: 7Last Post: May 27th, 2010, 09:24 AM -
Is colt 1911 worth trading my Para 1911?
By Mity2 in forum GeneralReplies: 48Last Post: December 9th, 2008, 01:56 PM -
Penn State Mech. Engineering - Opinions?
By Suburban in forum GeneralReplies: 14Last Post: December 5th, 2007, 01:08 PM -
1911 .22 Conversion Advice
By st.marys in forum GeneralReplies: 15Last Post: November 22nd, 2007, 05:39 PM -
.22 conversion for 1911's
By diputs in forum GeneralReplies: 8Last Post: April 8th, 2007, 07:37 PM
Bookmarks