Results 1 to 10 of 18
Thread: Car15 Clone?
-
April 21st, 2020, 08:14 PM #1
Car15 Clone?
i really like the looks of these rifles. i currently have a Colt 6920. is this just a matter of getting a stamp then buying the upper>? ive seen some online for sale without the bolt group but id prefer to buy a complete rifle. im not into swapping parts every time i want to shoot. ive also seen the ones from Brownells and Troy but not interested in them. i like the EXACT setup below.
Last edited by bravo30; April 21st, 2020 at 08:17 PM.
-
April 21st, 2020, 09:30 PM #2
Re: Car15 Clone?
Well , that one would have to be a SBR. Barrel and PERMANANTLY attached flash hider must be at least 16in.
Many later USGI CAR-15s (XM-177E1) were built on repurposed M-16 receivers.
https://en.wikipedia.org/wiki/CAR-15I don't speak English , I talk American!
-
April 21st, 2020, 09:33 PM #3
Re: Car15 Clone?
Mmmm... sexy gravel!
I called to check my ZIP CODE!....DY-NO-MITE!!!
-
April 21st, 2020, 09:48 PM #4
-
April 21st, 2020, 09:49 PM #5
-
April 21st, 2020, 10:16 PM #6Grand Member
- Join Date
- Aug 2014
- Location
-
Pittsburgh,
Pennsylvania
(Allegheny County) - Posts
- 1,092
- Rep Power
- 20694361
-
April 21st, 2020, 10:19 PM #7
-
April 21st, 2020, 10:49 PM #8Grand Member
- Join Date
- Mar 2009
- Location
-
Southwest,
Pennsylvania
(Washington County) - Posts
- 1,942
- Rep Power
- 21474853
Re: Car15 Clone?
I built a Colt Commando 733 clone a few years ago, if that counts. Its an 11.5" carbine with the C7 upper and no moderator.
I SBRed a Nodak Spud A2 gray lower and the upper is a Colt, but I may replace it because it's a large pin upper and my lower is not. It currently has an offset bushing in the front takedown hole of the upper.
I used a spikes 11.5" light weight barrel assembly and colt skinny handguards. I can't remember where I got the car stock, but it is a reproduction. Oh, and the tube is a two position, also NDS.
This is the only picture I have handy. The other rifle is an AKS74U clone, from an 86 Tula kit.
-
April 22nd, 2020, 08:15 AM #9
-
April 22nd, 2020, 09:47 AM #10Grand Member
- Join Date
- Mar 2009
- Location
-
Southwest,
Pennsylvania
(Washington County) - Posts
- 1,942
- Rep Power
- 21474853
Re: Car15 Clone?
If you're looking for parts:
Stripped C7 upper:
https://www.tntesales.com/c7-c8-m16e...pper-receiver/
Spikes CHF 11.5" barrel (would need populated)
https://www.righttobear.com/spikes-t...sb51106-lw.htmLast edited by marinville; April 22nd, 2020 at 09:53 AM.
Similar Threads
-
WTS: DoubleStar CAR15 - minty new w/goodies!
By The_War_Wagon in forum GeneralReplies: 2Last Post: May 6th, 2008, 12:19 PM -
WTS/WTT: CAR15 goodies!
By The_War_Wagon in forum GeneralReplies: 0Last Post: August 7th, 2007, 01:35 PM
Bookmarks