Pennsylvania Firearm Owners Association
Tab Content
  • Delkal's Avatar
    July 13th, 2020, 12:33 PM
    The sheriff just announced they will be extending the hours of the Levittown office and on certain nights they will be open till 8:00! Two big...
    28 replies | 1443 view(s)
  • Delkal's Avatar
    July 11th, 2020, 04:07 PM
    I got mine renewed 2 months ago. Last I heard the Levittown office was closed. I would recommend you going to Doylestown anyway since you will get...
    28 replies | 1443 view(s)
  • Delkal's Avatar
    July 10th, 2020, 08:00 PM
    Its kind of a misleading article. With the picture of Gramps with his workshop milling machine they make it sound like the bill is about banning...
    36 replies | 977 view(s)
  • Delkal's Avatar
    July 10th, 2020, 04:02 PM
    I had an older model Sport HD 3x9x40 AO for at least 10 years. It had good optics and a clear focus with the ability to adjust parallax down to 50...
    3 replies | 120 view(s)
  • Delkal's Avatar
    July 8th, 2020, 03:59 PM
    A 250 FPS increase in velocity shooting the same weight bullet is a significant jump in performance. For a 50-100 FPS I would concede there is not...
    64 replies | 53486 view(s)
  • Delkal's Avatar
    July 7th, 2020, 05:28 PM
    If they are just some light freckles use some OOOO steel wool and some oil and scrub all of the surface rust off. OOOO steel wool will not hurt a...
    17 replies | 384 view(s)
  • Delkal's Avatar
    July 5th, 2020, 10:12 AM
    Delkal replied to a thread Sticky in Rifles
    I use 1:1 linseed and turpentine. I don't think lacquer thinner will work since they usually contain alcohol and acetone. You will have to check...
    20 replies | 440 view(s)
  • Delkal's Avatar
    July 3rd, 2020, 10:05 PM
    Delkal replied to a thread Sticky in Rifles
    Here is my stock refinishing procedure that I posted on the CMP forums many years ago.....found it on my computer. This goes into more detail than...
    20 replies | 440 view(s)
  • Delkal's Avatar
    July 3rd, 2020, 08:57 PM
    Delkal replied to a thread Sticky in Rifles
    Boiled linseed already has hardeners in it and will dry if you add thin coats and give it time to dry between applications. If you start running out...
    20 replies | 440 view(s)
  • Delkal's Avatar
    July 3rd, 2020, 08:13 PM
    Delkal replied to a thread Sticky in Rifles
    Linseed oil can give a beautiful finish but it takes time to do a gunstock right. You need to wipe the smallest amount on and rub it with your...
    20 replies | 440 view(s)
  • Delkal's Avatar
    July 2nd, 2020, 02:00 PM
    Delkal replied to a thread Some 870 questions in Shotguns
    This^^^ I never handled or shot a mag loaded 870 but it seems like a silly solution to a problem that does not exist. A standard 870 with a mag...
    9 replies | 277 view(s)
  • Delkal's Avatar
    June 28th, 2020, 09:59 PM
    Delkal replied to a thread S&W Shield in Pistols
    I did pay over $100 less for a Gen 1 with the old rebate but like others have mentioned those prices are gone now. This was my first plastic pistol...
    8 replies | 358 view(s)
  • Delkal's Avatar
    June 28th, 2020, 05:16 PM
    Bullet drop is calculated by the muzzle velocity and the ballistic coefficient of the bullet. That is all you need to know. Since the 223 starts...
    9 replies | 375 view(s)
  • Delkal's Avatar
    June 26th, 2020, 08:31 PM
    Delkal replied to a thread Reloading question in General
    A slight crimp is good. You need to set the crimp so you remove all of the case bell from the expander die and I always go a little more. There is...
    19 replies | 543 view(s)
  • Delkal's Avatar
    June 26th, 2020, 05:37 PM
    Delkal replied to a thread Reloading question in General
    Checking every round for a correct OAL is worthless if you never determined if the OAL was correct in the first place. It sounds like you got a...
    19 replies | 543 view(s)
  • Delkal's Avatar
    June 26th, 2020, 05:10 PM
    You are correct.......I did not think about someone with a 7 1/2 inch door and a concrete door frame. But residential doors are pretty much a...
    33 replies | 1199 view(s)
  • Delkal's Avatar
    June 26th, 2020, 01:47 PM
    There is an exemption in the bill for firearms made without serial numbers that were manufactured before 1968.
    36 replies | 1537 view(s)
  • Delkal's Avatar
    June 26th, 2020, 11:37 AM
    Delkal replied to a thread Reloading question in General
    Put one round in a mag and push it down with the back of a pencil. See where it is getting jammed up. It should be easy to reseat the bullet a...
    19 replies | 543 view(s)
  • Delkal's Avatar
    June 25th, 2020, 11:19 PM
    Just about anyone can kick a door inwards if they try hard enough. The only thing holding it is a thin piece of the door frame where the inch of a...
    33 replies | 1199 view(s)
  • Delkal's Avatar
    June 25th, 2020, 05:41 PM
    Adding a little extra protection to the drywall is not a bad idea (mostly for fire protection) but don't go overboard. Especially if the door with...
    33 replies | 1199 view(s)
More Activity
About Delkal

Basic Information

Location Information
City:
Richboro
State:
Pennsylvania
County:
Bucks

Statistics


Total Posts
Total Posts
2,077
Posts Per Day
0.76
General Information
Last Activity
July 13th, 2020 08:47 PM
Join Date
January 21st, 2013
Referrals
0