Pennsylvania Firearm Owners Association

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.
Welcome to the Pennsylvania Firearm Owners Association Forum, we hope you like what you find here and we strongly encourage you to register for an account with us, especially if you are from Pennsylvania. Once registered you will have access to participate in our community. Thanks for visiting and we hope you become a regular!
Attention! There has been an influx of scammer signups!

The method of operation is to private message you and tell you that you should contact such 'n such person at a given email address.

Please report the private messages. Staff will ban the offender, and I will implement an IP ban. Unfortunately these scammers are using VPN/proxy services, which may mean your VPN/proxy may be blocked.
Attention! About VPN's and foreign IP addresses.

When signing up, do so from a US based Internet Service Provider. Turn off any VPN/safe-browsing feature. Failure to do so will result with your new account denied.

If you run into a IP ban afterwards as a member, again - turn off your VPN or switch servers. We do not ban legit Internet Service Providers from the USA(exception for certain individual IP addresses). Free VPN's tend to get banned too. We try not to ban legit subscription VPN services, but they rarely label their IP blocks correctly.

If you run into an IP ban, it likely wasn't you.

Activity Stream

Filter

Sort By	Time	Show
Recent Recent Popular Popular	Anytime Anytime Last 24 Hours Last 24 Hours Last 7 Days Last 7 Days Last 30 Days Last 30 Days	All All Photos Photos Forum Forums

Older Activity
March 28th, 2023, 11:28 PM

Emptymag replied to a thread Marlin 336 is back in Rifles

What year were they last produced?

see more

6 replies | 99 view(s)
March 28th, 2023, 10:49 PM

Emptymag replied to a thread What is inside a ar15 buffer in General

Yes. Well, I mean depends on the caliber. 9mm and such need a heavier buffer, but yeah, for 5.56 a standard carbine weight buffer and standard...

see more

10 replies | 207 view(s)
March 28th, 2023, 10:26 PM

bogey1 replied to a thread What is inside a ar15 buffer in General

Instead of starting a new thread, is a carbine buffer/spring ok to use in a brace tube?

see more

10 replies | 207 view(s)
March 28th, 2023, 09:32 PM

Lshaw replied to a thread [Want To Sell] Browning X-Bolt PRO McMillan Long Range 6.5CM | Pittsburgh | in Firearms

Price drop!

see more

6 replies | 601 view(s)
March 28th, 2023, 09:28 PM

bogey1 replied to a thread What is inside a ar15 buffer in General

Never knew any of this.. It's like slice bread was reinvented:D

see more

10 replies | 207 view(s)
March 28th, 2023, 09:07 PM

Rosco the Iroc replied to a thread ATF Stepping Up The Pressure in National

I got to renew this year. Can't wait to see the shitshow that shows up on my doorstep.

see more

11 replies | 477 view(s)
March 28th, 2023, 09:07 PM

Woodwanderer replied to a thread What is inside a ar15 buffer in General

Easier way to find this out is to buy an odinworks adjustable carbine buffer ;) no roll pin to remove, back end has a hex cap screw that removes and...

see more

10 replies | 207 view(s)
March 28th, 2023, 09:05 PM

Rosco the Iroc replied to a thread What is inside a ar15 buffer in General

Anything is a dildo if your brave enough.

see more

10 replies | 207 view(s)
March 28th, 2023, 09:02 PM

ForeverPA replied to a thread THE OAKS - March 31, April 1 & 2 - Eagle Shows in Gun Shows

So I am out a box of ammo as soon as walk in ?

see more

4 replies | 226 view(s)
March 28th, 2023, 08:54 PM

USMCGRUNT replied to a thread Gunsmith / Philly area in Gunsmithing

Will do. Thanks again!

see more

4 replies | 50 view(s)
March 28th, 2023, 08:48 PM

TacticalSpeed started a thread [Want To Buy/Trade] AR-15 lowers in Firearms

Anyone have any for sale/trade? Stripped preferred, but will consider completed or partially completed

see more

0 replies | 37 view(s)
March 28th, 2023, 08:47 PM

SteveWag replied to a thread a1 rear sight drum in Gunsmithing

Try to obtain an A1 REAR sight tool. Works so much better than a bullet. Note the there are tools for A1/A2 FRONT sights A1 has five prongs and A2...

see more

4 replies | 106 view(s)
March 28th, 2023, 08:46 PM

Walleye Hunter replied to a thread Gunsmith / Philly area in Gunsmithing

Send him a PM at CDI would be best.

see more

4 replies | 50 view(s)
March 28th, 2023, 08:43 PM

USMCGRUNT replied to a thread Gunsmith / Philly area in Gunsmithing

Great to hear, thank you! Do you know if there is a website or number I can call?

see more

4 replies | 50 view(s)
March 28th, 2023, 08:42 PM

bogey1 replied to a thread The Victims of Temple University in Philadelphia

My daughter went to winder for 7 years. You find yourself on the wrong side of the tracks down there, watch out.

see more

169 replies | 6230 view(s)
March 28th, 2023, 08:42 PM

TacticalSpeed replied to a thread Pit viper in Pistols

I can afford it. It's still not worth $7k to me. Just cannot justify that in my head

see more

15 replies | 498 view(s)
March 28th, 2023, 08:39 PM

bogey1 replied to a thread What is inside a ar15 buffer in General

Instead of changing the spring change the weights in the buffer. Also, that buffer can be used against your enemy. Just thing of the force exerted...

see more

10 replies | 207 view(s)
March 28th, 2023, 08:31 PM

Story replied to a thread Open Carry In Car in Concealed & Open Carry

Are we there yet?

see more

52 replies | 1510 view(s)

More Activity

All times are GMT -4. The time now is 12:04 AM.