Results 1 to 10 of 16
Thread: Incomplete Brass Ejection
-
January 20th, 2010, 10:32 PM #1
Incomplete Brass Ejection
Is this a typical problem with Dan Wesson guns? Is it typical with the Point Man 2?
If not, where do I start looking for reasons?
Clean gun. Brand new. Cheap ammo...
Is it a typical problem with PMC Bronze .45 ACP?
edit: Happens with both the original mag and the extra.
-
January 21st, 2010, 12:20 AM #2
-
January 21st, 2010, 12:28 AM #3
Re: Incomplete Brass Ejection
I mean the brass gets stuck in the action on its way out. Not every time, but far too often. I'd guesstimate 1 in every 8 or 10 shots.
-
January 21st, 2010, 12:36 AM #4
Re: Incomplete Brass Ejection
When you are called a racist, it just means you won an argument with an Obama supporter.
-
January 21st, 2010, 12:43 AM #5
Re: Incomplete Brass Ejection
Get her lubed/wet.
Hold her really tight......
Squeeze one off.......and see if the ejection is......adequate.
Repeat as needed.
Lycanfeelingfriskythrope
I taught Chuck Norris to bump-fire.
-
January 21st, 2010, 12:52 AM #6
Re: Incomplete Brass Ejection
Sorry. Limp-Wristing? If it's what I think it is, then no. I'd lose all the skin on my right wrist if I let that happen during archery.
But just to be sure, please explain to a brand new handgun user...
Lycanthrope...
I'm looking at your little bumper sticker and your post above and wondering What, exactly, you're saying you can hit...
-
January 21st, 2010, 12:57 AM #7
Re: Incomplete Brass Ejection
Fuzzy- Limp wristing is not holding the gun tightly enough with your dominant hand. When the gun is fired, if not held on tightly, the lack of grip can cause the slide to lose momentum (i guess that's how you would word it) and that would cause the internals not to perform to their full potential is ejecting the spent casing.
Weak loads can cause this to but isn't usually the case with factory ammo. The gun needing to be broken in could also be a factor but try to stiffen up a bit to see if that helps..
Check this video out
Last edited by Smalls; January 21st, 2010 at 01:01 AM.
-
January 21st, 2010, 01:06 AM #8
Re: Incomplete Brass Ejection
Actually, in most modern two handed grips, it's the non dominant hand that controls flip...............
Shameless ripoff from Google:
Keeping the weak hand up against the trigger guard and camming the weak hand forward.....so the thumb goes forward, but the palm stays in place......plays the most part in controlling flip......and therefore, combatting "limpwristing".
For many people the grip is about right if the weak thumb and the strong index finger (out of the trigger guard and along the frame) are about even when looking at the gun from above.
Lycanneverparktheweakhandunderthemagthrope
I taught Chuck Norris to bump-fire.
-
January 21st, 2010, 01:06 AM #9
Re: Incomplete Brass Ejection
My money says that's what's happening. And Not what I thought based on the words used for it. I'll give it a shot in 12 hours or so.
The way the casing is getting stuck in the action in the video is exactly how it's getting stuck in my 1911.
-
January 21st, 2010, 01:06 AM #10
Re: Incomplete Brass Ejection
When you are called a racist, it just means you won an argument with an Obama supporter.
Similar Threads
-
New incomplete Spikes 22 upper assembly
By arjohnson in forum GeneralReplies: 1Last Post: September 3rd, 2009, 12:22 AM -
LMT AR Ejection issues
By emsjeep in forum GeneralReplies: 20Last Post: August 25th, 2009, 01:41 PM -
Brass ejection problems- AR-15
By tec in forum GeneralReplies: 20Last Post: June 17th, 2008, 10:37 AM -
The other side of an incomplete CCW revocation explanation
By pex in forum GeneralReplies: 1Last Post: May 6th, 2008, 05:32 PM -
AR ejection direction
By Hawk in forum GeneralReplies: 10Last Post: February 15th, 2008, 08:38 PM
Bookmarks