Results 1 to 7 of 7
Thread: Issues with a S.A. 1911 Loaded
Hybrid View
-
January 15th, 2010, 03:01 PM #1Active Member
- Join Date
- Dec 2008
- Location
-
reading,
Pennsylvania
(Berks County) - Posts
- 102
- Rep Power
- 36
Issues with a S.A. 1911 Loaded
So I bought my first 1911. I always wanted one and finally sucked it up and bought a springfield armory parkerized loaded model. I have had it to the range twice now and here are the issues I'm having. I have put about 200 rounds down it so far and I've had about a half dozen failures to extract, and they are always on the last round. I'll try my best to explain the casing position. Imagine the casing coming straight back from the chamber and than the primer end drops down against the magazine causing the casing to be jammed in there on an angle. At this point I cant release the magazine to remove the casing so I have to pry the casing out. I am also having a problem with the front sight. The spring pin that holds the sight in keeps working its way up. I pushed it down a few times until it actually came out far enough where the front sight fell out of the dovetail onto the ground. Has anyone else had these problems with this particular gun, and if so how did you correct them.
-
January 15th, 2010, 03:07 PM #2
Re: Issues with a S.A. 1911 Loaded
I've had front sight pins walk on a few different makes of pistols. I normally put some red loctite or superglue on the pin and re-install. I normally only do this if I'm happy with the original sight though, since it makes future removal a pain. The other issue could be the extractor, magazine, or a bit of both? I've had 1911's do all sorts of weird things with one brand of magazine and not others. I'd say try Wilson 47D mags or have someone check extractor tension if the mag doesn't resolve the issue. Or...contact Springfield and have them fix the weapon up, they do have a very nice warranty.
-
January 15th, 2010, 04:24 PM #3
Re: Issues with a S.A. 1911 Loaded
Sounds like a type of smokestack failure.
Try gripping the gun EXTRA tight and see if this fixes it. Also....make sure the gun is well lubed. And....how far is this gun throwing the empty casings.....
Lycanneedsmoreinfothrope
I taught Chuck Norris to bump-fire.
-
January 15th, 2010, 05:04 PM #4Active Member
- Join Date
- Dec 2008
- Location
-
reading,
Pennsylvania
(Berks County) - Posts
- 102
- Rep Power
- 36
-
January 15th, 2010, 06:04 PM #5Super Member
- Join Date
- Jan 2008
- Location
-
Philadelphia,
Pennsylvania
(Philadelphia County) - Posts
- 831
- Rep Power
- 9496278
Re: Issues with a S.A. 1911 Loaded
I believe that the issues you describe would be the Mag,
Try other mags.
As far as the locktite, Get the stuff that when you heat you'll be able to remove the pin,, It is the weaker stuff and will work just fine for you.
Peter
-
January 15th, 2010, 07:20 PM #6Junior Member
- Join Date
- Jan 2010
- Location
-
West Grove,
Pennsylvania
- Posts
- 1
- Rep Power
- 0
Re: Issues with a S.A. 1911 Loaded
Simple checks
Check the extractor by removing the slide from the frame. Slide an empty shell casing up from the bottom and onto the breechface. You should be able to let go and the extractor should hold it loosely. Too tight can cause failure to feed, too loose will cause failure to extract.
Is the "Ejector" still there? And is it tight? The ejector tip on a .45 is pretty short but it has to be there. And it can't move.
After that.... assuming you prove it's not the magazines. You need somebody to look at it for you.
-
January 15th, 2010, 04:44 PM #7Active Member
- Join Date
- Dec 2008
- Location
-
reading,
Pennsylvania
(Berks County) - Posts
- 102
- Rep Power
- 36
Re: Issues with a S.A. 1911 Loaded
My plan for the front sight was to loctite it in. Just sucks that a brand new gun would have an issue like this. I was leaning towards the magazine due to the fact its always the last round that jams. Although I did have one failure to feed half way through a mag in which the cartridge would only load about 7/8's of the way into the chamber. I pulled it out and loaded it in the mag and than it cycled fine.
Similar Threads
-
1911 safety issues with leather holster
By tdyoung58 in forum GeneralReplies: 0Last Post: April 1st, 2009, 09:18 PM -
new Kimber 1911 issues
By Decholder in forum GeneralReplies: 29Last Post: March 12th, 2009, 02:13 PM -
My new SA SS 1911 Loaded.
By Mity2 in forum GeneralReplies: 9Last Post: July 9th, 2008, 10:04 AM -
WTS: Springfield 1911 Loaded
By slicknick131 in forum GeneralReplies: 2Last Post: May 20th, 2008, 07:05 PM
Bookmarks