Pennsylvania Firearm Owners Association
Results 1 to 4 of 4
  1. December 9th, 2009, 04:51 PM #1
    BIRTHMACHINE's Avatar
    BIRTHMACHINE
    BIRTHMACHINE is offline Active Member
    Send a message via AIM to BIRTHMACHINE Send a message via Yahoo to BIRTHMACHINE
    Join Date
    Sep 2008
    Location
    philly, Pennsylvania
    (Philadelphia County)
    Age
    42
    Posts
    114
    Rep Power
    16

    Default Hk USC/ump milling

    Before I ask this question let me make clear that if I were to start the project it would be done in compliance with all parts laws.

    I would like to know what in the upper needs to have material milled out to take the high cap clip? Also, if a ump lower is to be used, is there mods for the USC upper and ump lower to fit? Has anyone tried to cut the factory USC into a pistolgrip and perhaps added a folding stock to the factory USC. Just trying to figure out the cheapest way.
    Reply With Quote Reply With Quote
  2. December 9th, 2009, 06:02 PM #2
    mojo's Avatar
    mojo
    mojo is offline Grand Member
    Join Date
    Mar 2008
    Location
    Pittsburgh, Pennsylvania
    (Allegheny County)
    Posts
    3,262
    Rep Power
    11858

    Default Re: Hk USC/ump milling

    too bad Ronnie isn't on here any more. He went through the complete conversion process himself. He would have been able to help you.

    Sorry, can't help.
    Quote Originally Posted by GunLawyer001 View Post
    If the police could confiscate all of your guns and ammo using just one van, then you didn't own enough guns or ammo.
    WTB - NDS3 or NDS1 receiver FTF
    Reply With Quote Reply With Quote
  3. December 10th, 2009, 06:53 AM #3
    YBNORMAL's Avatar
    YBNORMAL
    YBNORMAL is offline Grand Member
    Join Date
    Jun 2009
    Location
    Home, Pennsylvania
    (York County)
    Age
    44
    Posts
    1,099
    Rep Power
    7799421

    Default Re: Hk USC/ump milling

    Where is Ronnie? I enjoyed his HK pics immensly!
    The smallest minority on earth is the individual. Those who deny individual rights cannot claim to be defenders of minorities.
    Ayn Rand
    Reply With Quote Reply With Quote
  4. December 10th, 2009, 09:18 AM #4
    mojo's Avatar
    mojo
    mojo is offline Grand Member
    Join Date
    Mar 2008
    Location
    Pittsburgh, Pennsylvania
    (Allegheny County)
    Posts
    3,262
    Rep Power
    11858

    Default Re: Hk USC/ump milling

    Quote Originally Posted by YBNORMAL View Post
    Where is Ronnie? I enjoyed his HK pics immensly!
    Took time off for his real life.
    Quote Originally Posted by GunLawyer001 View Post
    If the police could confiscate all of your guns and ammo using just one van, then you didn't own enough guns or ammo.
    WTB - NDS3 or NDS1 receiver FTF
    Reply With Quote Reply With Quote
« Previous Thread | Next Thread »

Similar Threads

  1. Milling machine
    By BAD_KARMA in forum General
    Replies: 0
    Last Post: May 10th, 2009, 08:21 PM
  2. WTS: Lathemaster ZAY7045 Milling Machine *Local Pick Up Only*
    By John@JCDLESales in forum General
    Replies: 1
    Last Post: October 7th, 2008, 11:19 AM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules