Pennsylvania Firearm Owners Association

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.
Welcome to the Pennsylvania Firearm Owners Association Forum, we hope you like what you find here and we strongly encourage you to register for an account with us, especially if you are from Pennsylvania. Once registered you will have access to participate in our community. Thanks for visiting and we hope you become a regular!
Attention! There has been an influx of scammer signups!

The method of operation is to private message you and tell you that you should contact such 'n such person at a given email address.

Please report the private messages. Staff will ban the offender, and I will implement an IP ban. Unfortunately these scammers are using VPN/proxy services, which may mean your VPN/proxy may be blocked.
Attention! About VPN's and foreign IP addresses.

When signing up, do so from a US based Internet Service Provider. Turn off any VPN/safe-browsing feature. Failure to do so will result with your new account denied.

If you run into a IP ban afterwards as a member, again - turn off your VPN or switch servers. We do not ban legit Internet Service Providers from the USA(exception for certain individual IP addresses). Free VPN's tend to get banned too. We try not to ban legit subscription VPN services, but they rarely label their IP blocks correctly.

If you run into an IP ban, it likely wasn't you.

Results 1 to 1 of 1

Thread: Ron's Gunsmithing

Thread Tools
Display
- Linear Mode
- Switch to Hybrid Mode
- Switch to Threaded Mode

March 9th, 2009, 11:47 PM #1
MTechnik

View Profile

View Forum Posts

Private Message

Grand Member
Join Date

Jun 2007

Location

West Chester, Pennsylvania
(Chester County)

Posts

1,155

Rep Power

67518
Ron's Gunsmithing

Met him at the range (SCCFSA) this weekend, got his card:

FFL Dealer
Full Service Repairs
Hot blueing
Ron
Boothwyn PA
610-485-8457

He has a shop in the side of his home and works out of there.

Reply With Quote

Quick Navigation General Top

Site Areas
Settings
Private Messages
Subscriptions
Who's Online
Search Forums
Forums Home
Forums
Forum
Discussion
Law & Politics
1. Pennsylvania
2. National
Marketplace
Events
Private Forums
1. PAFOA Club
Regions
1. Lake Erie Region
  1. Crawford
  2. Erie
  3. Mercer
  4. Venango
2. Allegheny National Forest Region
  1. Cameron
  2. Clarion
  3. Clearfield
  4. Elk
  5. Forest
  6. Jefferson
  7. McKean
  8. Potter
  9. Tioga
  10. Warren
3. Valleys of the Susquehanna Region
  1. Centre
  2. Clinton
  3. Columbia
  4. Juniata
  5. Lycoming
  6. Mifflin
  7. Montour
  8. Northumberland
  9. Snyder
  10. Union
4. Pocono Mountain Region
  1. Bradford
  2. Carbon
  3. Lackawanna
  4. Luzerne
  5. Monroe
  6. Pike
  7. Schuylkill
  8. Sullivan
  9. Susquehanna
  10. Wayne
  11. Wyoming
5. Lehigh Valley & Philadelphia Region
  1. Bucks
  2. Chester
  3. Delaware
  4. Lehigh
  5. Montgomery
  6. Northampton
  7. Philadelphia
6. PA Dutch Country/Hershey Region
  1. Adams
  2. Berks
  3. Cumberland
  4. Dauphin
  5. Franklin
  6. Lancaster
  7. Lebanon
  8. Perry
  9. York
7. Laurel Highlands Region
  1. Bedford
  2. Blair
  3. Cambria
  4. Fayette
  5. Fulton
  6. Greene
  7. Huntingdon
  8. Indiana
  9. Somerset
  10. Westmoreland
8. Pittsburgh Region
  1. Allegheny
  2. Armstrong
  3. Beaver
  4. Butler
  5. Lawrence
  6. Washington
Miscellaneous
1. The Lounge

« Previous Thread | Next Thread »

Similar Threads

getting into gunsmithing

By Roger41 in forum General

Replies: 12
Last Post: February 25th, 2008, 09:11 PM
Burwell Gunsmithing??

By senorlinc in forum General

Replies: 8
Last Post: February 4th, 2008, 10:45 PM
Gunsmithing in PA

By mick in forum General

Replies: 6
Last Post: November 6th, 2007, 10:54 PM
Learning gunsmithing AGI?

By Roger41 in forum General

Replies: 2
Last Post: January 19th, 2007, 04:43 PM
Gunsmithing course

By 91xlt in forum General

Replies: 8
Last Post: December 22nd, 2006, 07:00 PM