Results 1 to 4 of 4
Thread: M44 Bent Front Sight
-
March 11th, 2007, 03:07 PM #1
M44 Bent Front Sight
My first impulse is to try to get "bang" it back into shape as it looks like the elevation may be ok. The center post also seems ok so the damage may just be cosmetic.
The more I think of it, a ammo box must have fell on it during the drive home. No way I would missed this at the show.
-
March 11th, 2007, 03:38 PM #2
Re: M44 Bent Front Sight
That does look mostly cosmetic and minor. If I were you, I would drop a box a shells on it from the opposite direction. A rubber mallet and/or block of wood and hammer should have your girl looking prom pretty in no time!!
Guns are good.
If you can't fry it you shouldn't eat it
Loud pipes save lives
Mom spelled backwards spells....mom
"Please don't squeeze the Charmin." ~ Mr. Whipple
-
March 11th, 2007, 03:46 PM #3
Re: M44 Bent Front Sight
LOL, well I didn't go with the ammo box from a different direction route and a rubber mallet I thought would be insulting to a 50+ year old battle rifle but here is where I am now. Since there is a hole on top of the sight I put bit in and "lovingly banged" that a bit. She may not yet be ready for the prom but she now has personality. What the Soviet army could not do in decades was accomplished in the back of a 4Runner.
Last edited by phillyd2; March 11th, 2007 at 03:56 PM.
-
March 14th, 2007, 11:17 AM #4
Re: M44 Bent Front Sight -hood-
I get it, I was under the impression the post was bent. I've seen this before, although I haven't seen a 91/30 with a distorted hood yet. The hood on M1938s and M44s is built very different from 91/30s. The 91/30 hood is machined from a block or blank, the M38 sight base is machined without the hood. When done, it's just a square base with a dovetail on the bottom. They bend a steel strap to the shape of the hood and weld it to the sides of the base. They performed the final machining with the hood attached, and that's how they get it so clean. If you look closely at your picture, you can see a faint seam where the hood's attached to the base.
The last 1938 carbine I fixed with a hood problem actually had hood separation on one side. I fixed it by straightening & aligning the parts, and silver soldering the joint. I chose silver solder instead of rewelding since welding would have been much more disruptive and alse required refinishing, assuming nothing went wrong. The weld did hold on one side, so it was more cosmetic than anything else.
Here's my current Aztec 1938. 1944 dated, all matching, original laminated 38 stock (not M44 stock). It needed some work. When I received it, the firing pin threads were nearly stripped. This means it could have fired at random, and possibly out of battery. The seller had just given me a lengthy run-around about a more serious issue with another Mosin, so I just replaced the firing pin & cocking piece and called it a day. I'm glad I did, as it gave a very pleasant surprise on the range.
It's finished in polyurethane over stain. The original finish had more contrast between the laminations, but literally fell off the gun under the lightest touch.
I waited until the last flake of the original finish settled to the floor before refinishing.
Similar Threads
-
Front Sight's Reality Series
By RugerNiner in forum GeneralReplies: 3Last Post: January 31st, 2007, 12:37 AM -
Focus on the front sight
By GRIZZLYBEAR in forum GeneralReplies: 1Last Post: January 3rd, 2007, 07:31 PM -
Please suggest a laser sight for my FN SLP
By Fullpatch in forum GeneralReplies: 2Last Post: November 13th, 2006, 11:38 PM -
Sight-in Days @ WCRC
By doug in forum GeneralReplies: 0Last Post: October 12th, 2006, 09:52 PM -
Sight-in Days @ WCRC
By doug in forum GeneralReplies: 0Last Post: October 12th, 2006, 09:31 PM
Bookmarks