Coronavirus Reloading Thread

**Hoppy** · March 22nd, 2020, 10:46 PM

HAHA, I used to be ocd, apparently I'm over it.

**JoshIronshaft** · March 22nd, 2020, 11:31 PM

Originally Posted by MD66948

Kramer,

What is your load Data on the 9mm subs?

I use 147gr blue bullet, 4.1gr power pistol, 1.110" OAL.

**JoshIronshaft** · March 22nd, 2020, 11:34 PM

Originally Posted by icp4life162005

You willing to teach?
Ill pay for the supplies and your time if i can take the ammo i roll home with me lol
Im like 5 minutes away btw. Valley forge.

There is good info in this thread.

http://forum.pafoa.org/showthread.php?t=355267

**Qtrborecrazy** · March 23rd, 2020, 08:30 AM

6.5 Creedmoor
Browning Hells Canyon Speed
Sierra 130 grain GameChanger
Federal 210 primers
43 grains of Reloder 16
Speeds 2772, 2777, 2777, 2795, 2772.
I’m going to kick it up another 1/2 grain, look for 2800 FPS.

**lts1ow** · March 23rd, 2020, 08:35 AM

6 creed
starline brass
110gr smk's
CCI primer
40.2gr 4350

Averaging 3010fps with a SD of 7

Have about 150 prepped/primed pieces of brass left and probably will load up another 100 this week.

**ianb1116** · March 23rd, 2020, 10:00 AM

Loaded a bunch over the last week.

~1500 12ga target loads to bust clays
Remington Hulls
Win Primers
Clay Dot powder
7/8oz reclaimed shot

Also loaded up some (500x) 9mm as my new scorpion seems to be chewing through it faster than anticipated.
124gr plated RN
4.1gr win 231
CCI primer

I want to finish the brick of primers but then I'll move on to 6.5 CM and .308 as my supplies are getting low.

No worries for .223/.45/9/12ga

**Qtrborecrazy** · March 23rd, 2020, 10:09 AM

Originally Posted by lts1ow

6 creed
starline brass
110gr smk's
CCI primer
40.2gr 4350

Averaging 3010fps with a SD of 7

Have about 150 prepped/primed pieces of brass left and probably will load up another 100 this week.

Its1ow, you liking the Starline brass? I bought 100 pieces for the 6.5. I also bought 124 grain hammer hunters and 117 grain sledge hammers. I should get a little more speed from both but haven’t had time to hit the range for some trigger time yet. I’m looking for 2900 for the hunters and 3k for the sledge hammers.

**Sgt.K** · March 23rd, 2020, 11:03 AM

Originally Posted by Hoppy

Cleaned some 9mm brass....

And a whole plate full of case lube on the left...

**lts1ow** · March 23rd, 2020, 12:22 PM

Originally Posted by Qtrborecrazy

Its1ow, you liking the Starline brass? I bought 100 pieces for the 6.5. I also bought 124 grain hammer hunters and 117 grain sledge hammers. I should get a little more speed from both but haven’t had time to hit the range for some trigger time yet. I’m looking for 2900 for the hunters and 3k for the sledge hammers.

Love it, their cheap (500pc/$250) and I am at four firings with one annealing and so far have had maybe two pieces with split necks.

**MD66948** · March 23rd, 2020, 04:32 PM

Originally Posted by icp4life162005

You willing to teach?
Ill pay for the supplies and your time if i can take the ammo i roll home with me lol
Im like 5 minutes away btw. Valley forge.

Kings Shooting Supplies in K of P used to give Reloading Classes especially for the Dillon Line of Products. I know they are getting ready to open their new in door range so they may no longer offer classes. If your interested I would check with Kings after this Chicom Virus starts to settle down.