Results 121 to 130 of 296
Thread: SEPA Milling Party?
-
January 30th, 2020, 10:54 AM #121
Re: SEPA Milling Party?
Calm down, this is an initial run to see if my equipment will do the job and get acquainted with the process. I did post that we would do this before gathering a large group and have it fail and some said that they would like to come and watch just the same. For all we know we could give it an attempt and see that we need more stuff.
Gender confusion is a mental illness
-
January 30th, 2020, 11:01 AM #122
Re: SEPA Milling Party?
Ha, OK. Blindsided me.
I do plan on trying to pick up a bit/end mill set made specifically for my jig.
I agree that we can't have too many end mills going into this.Galations 6:9...And let us not grow weary of doing good, for in due season we will reap, if we do not give up.
Ashli Babbitt - Patriot
-
January 30th, 2020, 11:32 AM #123
-
January 30th, 2020, 01:39 PM #124
Re: SEPA Milling Party?
OK, for those who had shown an interest in the initial trial we are set for 0930 Friday (tomorrow). This is a run to ensure that all should work for a larger gathering.
Gender confusion is a mental illness
-
January 30th, 2020, 04:56 PM #125
Re: SEPA Milling Party?
Great idea on the shakedown run! I'd be interested in attending a future party for sure.
-
January 30th, 2020, 06:54 PM #126
Re: SEPA Milling Party?
I have to work Friday, so I won't be able to make it.
Good luck all.
(Still no shipping on the jig, but the two lowers I ordered are in transit)
-
January 31st, 2020, 11:57 AM #127Active Member
- Join Date
- Jan 2013
- Location
-
Chester Springs,
Pennsylvania
(Chester County) - Posts
- 182
- Rep Power
- 15567429
Re: SEPA Milling Party?
if this started at 0930, we should be seeing reports of completed projects by now. Update?
-
January 31st, 2020, 11:58 AM #128
Re: SEPA Milling Party?
Rules are written in the stone,
Break the rules and you get no bones,
all you get is ridicule, laughter,
and a trip to the house of pain.
-
January 31st, 2020, 12:05 PM #129
Re: SEPA Milling Party?
Or after they get their fingers sewn back on...
Galations 6:9...And let us not grow weary of doing good, for in due season we will reap, if we do not give up.
Ashli Babbitt - Patriot
-
January 31st, 2020, 04:30 PM #130
Re: SEPA Milling Party?
LOL, I mean ROFLMFAO. In your dreams...in my dreams as well. It's a good thing we did it that way we did. Over five non-stop hours in and still not done one. Too bad none of yinz came over, you probably could have learned a whole lot of what not to do. First off it took a while to true the setup up and then we started milling. This is not a Bridgeport with balls the size of...well...me of course. It was slow and steady and learning what the machine can do and how to do it. Then I got tired of the slow progress and went like a bull in a china shop and broke one of the end mill bits. Fortunately we have more .
So...it seemed like the bit we started with started to get tired before we were done so more mill bits is important. Second, bits with short milling parts and longer shaft is important, that will let us go faster as the shaft won't eat up the jig like the milling end does if it's rubbing against the edge of the jig and we won't have to worry so much about getting close to the edge. You might have to see it to understand it but...longer shaft and short milling section, 1/2" of active part is sufficient. In the end I can still not give any idea of how long one will take to mill out once it's down pat but...since everyone has to do their own each will have to watch someone else do theirs so they can do one. Also, once things are figured out a video can be made that will help others out.Gender confusion is a mental illness
Similar Threads
-
Anyone want to have a milling party for their 80% receivers..
By edstephan in forum RiflesReplies: 24Last Post: January 26th, 2020, 04:03 PM -
AR milling jig
By jbraun948 in forum GunsmithingReplies: 0Last Post: March 10th, 2014, 03:32 AM -
Custom milling on my M&P Pro
By garyaug in forum PistolsReplies: 11Last Post: August 28th, 2013, 09:42 PM -
Hk USC/ump milling
By BIRTHMACHINE in forum GeneralReplies: 3Last Post: December 10th, 2009, 09:18 AM
Bookmarks