Results 1 to 10 of 11
Hybrid View
-
May 12th, 2018, 09:11 PM #1Member
- Join Date
- Jan 2013
- Location
-
Berks County,
Pennsylvania
(Berks County) - Posts
- 46
- Rep Power
- 0
Looking for someone to replace S&W 586 Front Sight
Specifically looking for someone near Allentown who can do it while I wait, even if it costs more. My local smith wants to hold a gun hostage for months and I will miss it too much while it's gone. Any help?
-
May 12th, 2018, 09:23 PM #2
Re: Looking for someone to replace S&W 586 Front Sight
CDI is in your area. Contact him and see what he has to say. He's one of the Good Guys!
http://forum.pafoa.org/member.php?u=23493Corruption is the default behavior of government officials. JPC
-
May 12th, 2018, 09:33 PM #3Member
- Join Date
- Jan 2013
- Location
-
Berks County,
Pennsylvania
(Berks County) - Posts
- 46
- Rep Power
- 0
Re: Looking for someone to replace S&W 586 Front Sight
Thank you - just PM'd him.
Any other leads?
-
May 12th, 2018, 09:59 PM #4Grand Member
- Join Date
- Aug 2010
- Location
-
South East of disorder
- Posts
- 3,581
- Rep Power
- 21474853
Re: Looking for someone to replace S&W 586 Front Sight
Do you have a replacement site or do you need one?
Aggies Coach Really ??? Take off the tin foil bro.
-
May 12th, 2018, 10:08 PM #5Member
- Join Date
- Jan 2013
- Location
-
Berks County,
Pennsylvania
(Berks County) - Posts
- 46
- Rep Power
- 0
Re: Looking for someone to replace S&W 586 Front Sight
I have the sight. It needs to be drilled and installed.
-
May 12th, 2018, 10:15 PM #6Grand Member
- Join Date
- Aug 2010
- Location
-
South East of disorder
- Posts
- 3,581
- Rep Power
- 21474853
-
May 13th, 2018, 11:31 AM #7Grand Member
- Join Date
- Mar 2009
- Location
-
Southwest,
Pennsylvania
(Washington County) - Posts
- 1,942
- Rep Power
- 21474853
Re: Looking for someone to replace S&W 586 Front Sight
Here is a brief summary of my DIY S&W front sight swap:
First of all, the factory roll pin is smaller than 1/16". I don't have and couldn't find a pin punch that small, so I beat a drill bit through there and dicked up the factory roll pin in the process.
I then decided to drill the revolver and new front sight to 1/16" (two drill bit sizes bigger) and install a 1/16" roll pin. I got roll pins and drill bits from brownels.
I used a hand drill and locked the revolver in a vise with some pine wood scraps that wouldn't marr the finish. I held the new sight in place with a couple vise clamps and more wood. Then I marked the drill bit at the desired depth with electrical tape and drilled halfway from each side. Finally, I knocked in the new roll pin and alls well.
It wasn't that difficult to do it myself, you just gotta sack up and do it. Otherwise you can pay somebody else and deal with the fact that probably no one will do it while you wait.
-
May 13th, 2018, 08:33 PM #8Member
- Join Date
- Jan 2013
- Location
-
Berks County,
Pennsylvania
(Berks County) - Posts
- 46
- Rep Power
- 0
Re: Looking for someone to replace S&W 586 Front Sight
Appreciate the tips folks but I'm not going near my firearms with power tools. I'd never forgive myself if I damaged anything. Besides, the guy from CDI is going to help me out.
Similar Threads
-
Change Low profile front gas block on AR to A2 style front sight
By OldKingKibitzer in forum GeneralReplies: 1Last Post: February 27th, 2016, 12:43 PM -
ANY Gunsmiths Near Centre County Replace AK Front Sight Bases???
By StingyGunner in forum GunsmithingReplies: 2Last Post: May 19th, 2013, 01:00 PM -
How hard is it to replace the front hand guard on an AR?
By carrguy1 in forum RiflesReplies: 17Last Post: July 7th, 2012, 12:00 PM
Bookmarks