Results 1 to 10 of 24
Thread: Removing Stain From Wood Stock
-
February 19th, 2018, 11:47 PM #1Senior Member
- Join Date
- Feb 2018
- Location
-
Bucks County,
Pennsylvania
(Bucks County) - Posts
- 269
- Rep Power
- 2102458
Removing Stain From Wood Stock
Hey guys...I have a newer Thompson rifle, and the maker tells me that the stocks are walnut, treated with boiled linseed oil.
Problem is, the butt stock is not well finished with sanding marks, etc and I'd like to make it nicer. If I lightly sand, I get color so I know they have some sort of stain. In order to make them smooth, some sanding is required and that will cause light spots.
Is there a product or technique that would allow me to draw the stain out so that I have a clean slate to work from?
My thought process is to get them right...then stain.
I've yet to find any good info on-line about this as most folks are looking to remove stains, like oil stains...not an actual wood color stain.
Thanks in advance for your thoughts!
-
February 20th, 2018, 07:30 AM #2
Re: Removing Stain From Wood Stock
Murphy's oil soap and/or Citristrip.
Owner Trigger Time LLc 01 FFL/NFA Saylorsburg, PA. Sales/Service/Transfers/Training
NRA CRSO/Pistol/Rifle/Shotgun inst. BSA Rifle/Shotgun Merit badge counselor. US Navy Marksmanship Team Staff
-
February 20th, 2018, 11:36 AM #3
Re: Removing Stain From Wood Stock
Citristrip for me too. I stripped stain off stairs to re-finish. Works amazingly and won't kill you when you sniff it.
Galations 6:9...And let us not grow weary of doing good, for in due season we will reap, if we do not give up.
Ashli Babbitt - Patriot
-
February 20th, 2018, 02:27 PM #4Grand Member
- Join Date
- Jan 2007
- Location
-
OUT TO LUNCH
- Posts
- 4,560
- Rep Power
- 21474858
Re: Removing Stain From Wood Stock
Let me qualify this by saying that I am far from a master craftsman when it comes to woodwork. I have refinished a few surplus military rifles though and used the EZ Off oven cleaner to strip the stocks. Spray on, let sit, spray off with hose. Allow to dry for several days. Again, not a pro, did this with old surplus rifles with ROUGH stocks. I am sure that there are commercially available products intended for the task.
-
February 20th, 2018, 09:20 PM #5Junior Member
- Join Date
- Feb 2018
- Location
-
Kittanning,
Pennsylvania
(Armstrong County) - Posts
- 8
- Rep Power
- 0
Re: Removing Stain From Wood Stock
There is nothing that will remove stain other than sanding it down the best that you can. Wood bleach will bleach it but you don't want to do that. What the other people have suggested is to remove finish, finish isn't stain, finish is the clear. Sand it down really good to the point where the color is somewhat consistent then stain again.
-
February 20th, 2018, 10:11 PM #6Senior Member
- Join Date
- Feb 2018
- Location
-
Bucks County,
Pennsylvania
(Bucks County) - Posts
- 269
- Rep Power
- 2102458
-
February 20th, 2018, 10:22 PM #7
Re: Removing Stain From Wood Stock
I have some wood in the workshop right now with some really old stain, probably 50 to 80yr's old. I'd be interested in a way to remove it, and was thinking about trying the Citristrip. If you want to wait, I can post my results in a few days. The wood that's out there doesn't really matter if it gets screwed up.
Rules are written in the stone,
Break the rules and you get no bones,
all you get is ridicule, laughter,
and a trip to the house of pain.
-
February 20th, 2018, 11:07 PM #8
Re: Removing Stain From Wood Stock
skip the easy off and mix some sodium hydroxide or purchase some pre-mixed. less chems in the raw product.
i have done a bunch of wood work and second the sanding. sand it all down even, the wood will lighten and once you're consistent go ahead and finish it again with the same color or slightly darker.
don't be afraid to blend your own stain colors and use oil based, water based is crap.
make sure you mix enough for the whole project if you're not just layering colors.
i always fail at applying a nice poly coat. no matter how hard i try, it's unsatisfactory to me. even wet sanding between coats @ 1000 grit.There is no way to make it out alive...
-
February 20th, 2018, 11:48 PM #9Senior Member
- Join Date
- Feb 2018
- Location
-
Bucks County,
Pennsylvania
(Bucks County) - Posts
- 269
- Rep Power
- 2102458
Re: Removing Stain From Wood Stock
Streaker69...that would be awesome!
I've been wanting to do this over the winter, but have been sidelined with sorting my Mom's estate, the house, etc. So, for obvious reasons....I've gotten nothing done on this project.
I'll be watching to see how it works. If it doesn't, I'm not against sanding as I want to fix some sanding marks in especially the butt stock that frankly, shouldn't have left the factory the way it is. I see it as an opportunity to make it really nice. (Now, we'll have to see how my skills are!)
-
February 21st, 2018, 09:57 AM #10Senior Member
- Join Date
- May 2011
- Location
-
Lancaster,
Pennsylvania
(Lancaster County) - Posts
- 338
- Rep Power
- 3650
Re: Removing Stain From Wood Stock
I refinished an old stevens model 311A as a gift for my father years ago. Here's what I did to strip the old stain and finish off the stock. You're going to need some cheesecloth, citristrip, and steel wool and or sand paper (both are optional).
1) separate the stock from the gun, removing any and all hardware.
2) bring a large pot to boil (if possible you want the pot to be of a size that you can rest the gun stock across the rims of the pot, letting the steam rise around it)
3) spray the stock down with citristrip, then cover with the cheesecloth.
4) rest the stock across the rims of the pot letting the steam rise over it. I probably did this for a few minutes then flipped it over. Added benefit of the steam is that it will pop out any dimples or indentations in the wood. I was amazed at how many of the dents and dings in the wood came right out.
5) pull the cheese cloth off and repeat steps above as necessary until the citristrip and cheese cloth pull all the stain out of the wood. If necessary you can scrub the stock a little with cheese cloth or steel wool to work off stubborn spots.
6) if you really want to smooth the wood out, it with with the steel wool or fine grit sand paper to knock down all the bits of wood raised by the steam.
7) let it dry and then smooth out with light grit sand paper to your liking and your ready to re-finish. I used one of the birchwood casey kits and some minwax stain, both are pretty inexpensive, and it turned out great.
Similar Threads
-
Removing paint from stock and barrel.
By bull2969 in forum GeneralReplies: 8Last Post: March 30th, 2009, 01:16 PM -
Remington 870 stock & forend + Ruger 10/22 wood stock
By Never_Enough in forum GeneralReplies: 0Last Post: March 16th, 2009, 03:31 PM -
Color to stain an AK wood stock?
By weaselchew in forum GeneralReplies: 20Last Post: February 3rd, 2009, 02:00 PM -
Could use an adviser on removing RPK Stock
By Winbettor in forum GeneralReplies: 0Last Post: August 1st, 2008, 05:32 PM
Bookmarks