Results 1 to 10 of 10
-
January 14th, 2018, 06:29 PM #1Senior Member
- Join Date
- Nov 2010
- Location
-
Drexel Hill,
Pennsylvania
(Delaware County) - Posts
- 396
- Rep Power
- 13066522
Installed Colt Medallions on a Nice Set of Wood Grips
What do you think? This is my Colt Government 380.
FYI, I used a half inch forstner bit(Removed most of the material), a dremel, sand paper and apoxie. The half inch bit got me close then I used a cone shaped aluminum oxide dremel bit both with a dremel and with my hand to make the fit perfect
Regards,
KobswLast edited by kobsw; April 27th, 2018 at 07:02 PM.
-
January 14th, 2018, 06:37 PM #2
Re: Installed Colt Medallions on a Nice Set of Wooden Grips
Nicely done,where did you get the medalions from?
There are no pacts between lions and men.
-
January 14th, 2018, 06:46 PM #3Senior Member
- Join Date
- Nov 2010
- Location
-
Drexel Hill,
Pennsylvania
(Delaware County) - Posts
- 396
- Rep Power
- 13066522
Re: Installed Colt Medallions on a Nice Set of Wooden Grips
TY....
I bought two sets of medallions from Amazon. One set was from AJAX and they were ok but the other set was from Numrich and they were very detailed so they're the ones I used.
KobswLast edited by kobsw; January 14th, 2018 at 11:14 PM.
-
January 14th, 2018, 07:08 PM #4
Re: Installed Colt Medallions on a Nice Set of Wooden Grips
Nice,that's a good looking case too.
There are no pacts between lions and men.
-
January 14th, 2018, 07:38 PM #5
Re: Installed Colt Medallions on a Nice Set of Wooden Grips
Looks great! It really adds a lot to the overall look of the pistol.
-
January 14th, 2018, 07:42 PM #6Senior Member
- Join Date
- Nov 2010
- Location
-
Drexel Hill,
Pennsylvania
(Delaware County) - Posts
- 396
- Rep Power
- 13066522
-
January 14th, 2018, 07:43 PM #7
Re: Installed Colt Medallions on a Nice Set of Wooden Grips
Very good looking grips
-
January 14th, 2018, 08:17 PM #8
Re: Installed Colt Medallions on a Nice Set of Wooden Grips
Nice job!
(Epoxy?)
-
January 14th, 2018, 09:23 PM #9Senior Member
- Join Date
- Nov 2010
- Location
-
Drexel Hill,
Pennsylvania
(Delaware County) - Posts
- 396
- Rep Power
- 13066522
-
January 21st, 2018, 12:28 AM #10Senior Member
- Join Date
- Nov 2010
- Location
-
Drexel Hill,
Pennsylvania
(Delaware County) - Posts
- 396
- Rep Power
- 13066522
Re: Installed Colt Medallions on a Nice Set of Wooden Grips
Updated pictures from Postimage.org.. No more hyperlinks or thumbnails for me.
Kobsw
Similar Threads
-
Need suggestions on 1911 grips. **Updated with new grips installed photo**
By bripro in forum PistolsReplies: 28Last Post: May 23rd, 2016, 07:20 AM -
Royden Leather, Wind Gap - Leather, grips, buckles, pins, medallions
By ungawa in forum ShopsReplies: 0Last Post: March 13th, 2010, 11:27 AM
Bookmarks