Pennsylvania Firearm Owners Association
Results 1 to 5 of 5
  1. #1
    Join Date
    May 2016
    Location
    Fenton, Missouri
    Posts
    74
    Rep Power
    214750

    Default Please help identify small part

    Found on floor where I clean my guns. Can anyone identify as part of Smith & Wesson 500 Magnum, Remington 1911 R1, or Sig Sauer P238? It's about .25 in diameter, and about .25 in long, the small shaft is about .125 diameter.

    http://imgur.com/TfaEDNM

    http://imgur.com/NmCOBRc

    http://imgur.com/40aoCK8

    I just took the plate off my 500 Magnum which exposed the trigger and all the internal stuff. Also took cylinder ejection mechanism apart.
    Hope someone can help.
    Thanks
    Bruce

  2. #2
    Join Date
    Aug 2009
    Location
    bloomsburg, Pennsylvania
    (Columbia County)
    Posts
    449
    Rep Power
    12983186

    Default Re: Please help identify small part

    It’s the Mainspring Housing Pin Lock to your Sig 238.
    http://www.gunpartscorp.com/Products/1512690.htm

    Check out part 33 on this diagram. It will show you were it goes.
    http://www.gunpartscorp.com/Manufact...397.htm?page=3

  3. #3
    Join Date
    Aug 2013
    Location
    Lehigh Valley, Pennsylvania
    (Lehigh County)
    Posts
    1,105
    Rep Power
    21474841

    Default Re: Please help identify small part

    I was going to suggest it fit the end of a spring, but looks like eagleclaw nailed it!
    Illegitimus non carborundum est

  4. #4
    Join Date
    May 2016
    Location
    Fenton, Missouri
    Posts
    74
    Rep Power
    214750

    Default Re: Please help identify small part

    Awesome. I ended up having to reset the ejection lever on the sear spring because I pushed it down too far while cleaning the gun. It must have popped out when I did that. Thanks a lot, eagleclaw. It's a relief to know where it goes. I had a heck of a time getting that sear spring in there just right. Not looking forward to that again.

    Bruce

  5. #5
    Join Date
    May 2016
    Location
    Fenton, Missouri
    Posts
    74
    Rep Power
    214750

    Default Re: Please help identify small part

    With the info provided was able to disassemble the 380, replace the part and reassemble it. I even made friends with the sear spring, was no problem to get it in there correctly.

Similar Threads

  1. Identify what I have in the box......
    By bripro in forum Gun Pictures
    Replies: 30
    Last Post: July 22nd, 2014, 10:15 PM
  2. [Want To Trade] 2,000 Winchester small rifle primers for small pistol
    By BerksCountyDave in forum Classifieds Archive
    Replies: 1
    Last Post: June 21st, 2011, 11:53 AM
  3. [CLOSED] Small wet tile saw, small table saw
    By ehidle in forum Classifieds Archive
    Replies: 0
    Last Post: October 25th, 2010, 08:46 PM
  4. Small boat for small lake
    By soup in forum General
    Replies: 1
    Last Post: March 31st, 2009, 02:28 PM
  5. Small part of my family!
    By LX Kid in forum General
    Replies: 7
    Last Post: July 27th, 2008, 10:39 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Local gun shops | Local shooting ranges | Philadelphia Shooting Ranges | Philadelphia Gun Shops | Pittsburgh Shooting Ranges | Pittsburgh Gun Shops