Results 11 to 18 of 18
-
May 3rd, 2017, 10:04 AM #11
Re: Looking for input from folks reloading for an M1A Scout rifle
Take the scope off and shoot it with the open sights if it shoots the same then it's a gun issue not the scope /rings/ mounts ect . Eliminate one variable at a time
-
May 4th, 2017, 11:46 AM #12
Re: Looking for input from folks reloading for an M1A Scout rifle
Thanks to all who offered ideas.
-
May 29th, 2017, 07:49 PM #13Active Member
- Join Date
- May 2009
- Location
-
Pacific NW,
Oregon
- Posts
- 109
- Rep Power
- 302699
Re: Looking for input from folks reloading for an M1A Scout rifle
What were the specific charge weights in the reloads ?..yours and his...
And BLC2 can be very fussing at Max charge weights.Last edited by bfoosh006; May 29th, 2017 at 08:00 PM.
-
May 31st, 2017, 11:40 AM #14
Re: Looking for input from folks reloading for an M1A Scout rifle
My 168 SMK loads allegedly duplicate the Federal Match used by military in propellant: 42.8gr IMR 4064. Do well in my Savage with 24" bbl. I suspect one of the things that may be upsetting the apple cart is the shorter scout barrel...plus whatever else is going on with his rifle or scope. I don't know his BLC2 loads.
-
June 5th, 2017, 02:43 PM #15Active Member
- Join Date
- May 2009
- Location
-
Pacific NW,
Oregon
- Posts
- 109
- Rep Power
- 302699
Re: Looking for input from folks reloading for an M1A Scout rifle
This.
While M1A's are fussy... it should shoot better then this thread says.
And I am not a fan of BLC2... it gets spooky at some point and will go over the pressure peak fast / all of a sudden.
Read this as well....
http://www.zediker.com/downloads/14_loading.pdf
-
June 19th, 2017, 11:15 AM #16Banned
- Join Date
- Jun 2017
- Location
-
Phoenix,
Arizona
- Posts
- 250
- Rep Power
- 0
Re: Looking for input from folks reloading for an M1A Scout rifle
If you are unable to fix the problem call Ron Smith of Smith Industries out here in Phoenix AZ. His family has been into that weapon for longer then I know. He can help you over the phone.
-
June 23rd, 2017, 12:17 PM #17
Re: Looking for input from folks reloading for an M1A Scout rifle
Sorry for my lack of response to the posted help. I only bump into this gentleman if we both happen to simultaneously come to the club range. Last time I saw him I gave him a list of suggestions I had assembled from these posts. I haven't seen him for a while.
-
August 4th, 2017, 09:37 AM #18Active Member
- Join Date
- May 2009
- Location
-
Pacific NW,
Oregon
- Posts
- 109
- Rep Power
- 302699
Re: Looking for input from folks reloading for an M1A Scout rifle
Also... I read an article / thread somewhere... that showed a abysmal factory crown job on the end of the barrels muzzle.
So if you see the gentleman again... you might mention that as well.
Similar Threads
-
I would like some input, folks (a WWYD?- scenario)
By Franky4Fingers in forum GeneralReplies: 38Last Post: December 23rd, 2013, 06:47 PM -
Reloading software input needed
By messeduprex in forum Ammunition & ReloadingReplies: 14Last Post: February 22nd, 2013, 07:45 PM -
new to the site and to reloading. input wanted
By ryans0z28 in forum Ammunition & ReloadingReplies: 17Last Post: May 29th, 2011, 08:12 PM -
Any other Scout rifle fans? New Savage Scout - w/ pics
By urbanamish99 in forum GeneralReplies: 12Last Post: November 1st, 2009, 10:53 PM
Bookmarks