Results 1 to 10 of 19
Thread: sear spring
-
March 7th, 2017, 05:43 PM #1
sear spring
I know I can't tell until I take this mini 1911 apart - but if the grip safety does not work ( no tension, just always engaged ) what would the most likely problem be - broken/damaged sear spring ?
-
March 7th, 2017, 09:10 PM #2
Re: sear spring
You mean its always on? Or it's always off? It may have slipped beside the finger of the spring. Drop the main spring housing out and look.
-
March 7th, 2017, 09:15 PM #3
Re: sear spring
That's odd...My first thought is in line with yours Cruzans. The sear spring leaf that extends outwards towards the grip safety may be the issue.
1) The grip safety leaf could have a burr that is hooked on the sear leaf and stuck. OR
2) The spring is broken, dislodged, somehow not functioning
3) There could be a burr or some interference on the grip safety itself interfering with the frame. However, if you know this gun was working before, this is unlikely.I'm only here for the wood c-rings.
-
March 7th, 2017, 09:44 PM #4
Re: sear spring
Thanks guys. Yes, safety is always off. The grip safety won't "bounce back". I'll be taking it down this weekend to check it out. I see Numerich has sear springs and pins if I need either - sear is actually out of stock so hopefully it's not that. I'll post what I find this weekend in case anyone else runs across the same issue
-
March 9th, 2017, 09:44 PM #5
Re: sear spring
Took it apart today and it's the sear spring. One "prong" is broken right off. Just ordered from Numerich. Hopefully, that is the only problem and I put it back in correctly
-
March 9th, 2017, 09:58 PM #6
Re: sear spring
Thats weird. I guess the temper was off.
-
March 18th, 2017, 08:56 PM #7
Re: sear spring
So bummed, thought I was going to add another "gunsmithing" job to my resume. Got the new sear spring, installed it, put everything back together, grip safety has nice tension now - high fiving myself ( might have that on security camera ) but then I tested it, and the hammer still drops regardless if the grip safety is pressed or not I text my lgs owner and he said one of the prongs - the one that rests on sear, might need to bent a bit. I bent her up a few different times, and nothing. Can't think of what else it could possibly be !
-
March 18th, 2017, 10:23 PM #8
Re: sear spring
There should be a prong on the inside of the grip safety that prevents the rear of the trigger bow from moving back far enough to affect the sear. Gripping the gun moves this prong up out of the way. Maybe the prong is too short or not aligned with the trigger bow. If you take off the grips and shine a light in there, maybe you can see what's going on.
-
March 18th, 2017, 10:38 PM #9
Re: sear spring
Thanks. I've been looking inside trying to figure it out but nothing so far. Started having a few beers after my failure to fix so I will pick up the battle again tomorrow - lol. Everything looks to be in the right place, grip safety has good tension/pressure, I'm stumped.
-
March 19th, 2017, 02:53 PM #10
Re: sear spring
Gun purchased new or used? If new, contact CS of factory. If used, try to figure out what previous owner did to "improve it".
Similar Threads
-
CZ82 Sear Spring.
By WoodsyHowl in forum GunsmithingReplies: 0Last Post: August 26th, 2014, 05:54 PM -
Just Installed a Police Trigger Sear Spring in HD Remington 870
By Capt Quahog in forum ShotgunsReplies: 5Last Post: September 30th, 2011, 09:39 PM -
91/30 sear
By Azzy in forum GunsmithingReplies: 1Last Post: March 30th, 2010, 10:22 PM -
WTS - H&K MP-5 Sear Gun
By m-1911 in forum GeneralReplies: 0Last Post: August 24th, 2008, 12:31 PM
Bookmarks