Results 1 to 10 of 10
-
November 16th, 2016, 02:51 PM #1Member
- Join Date
- Nov 2016
- Location
-
Lansdale,
Pennsylvania
(Montgomery County) - Posts
- 33
- Rep Power
- 0
How do I get the gun finish back on my SP101 cylinder?
Hello all,
Any suggestions on how can I get the black finish back on the cylinder of my SP101? I shot it a few times and now I have this ashy looking discoloration.
Thanks.
-
November 16th, 2016, 03:20 PM #2Grand Member
- Join Date
- Sep 2009
- Location
-
PENNSYLVANIA,
Pennsylvania
- Age
- 73
- Posts
- 3,788
- Rep Power
- 21474854
Re: How do I get the gun finish back on my SP101 cylinder?
Try Hoppes # 9 with a soft vinyl brush ! Our Taurus ultra-Lite has the same finish and will only clean up a bit better, it was made to be rust resistant to a degree ! MDT
-
November 16th, 2016, 03:21 PM #3
Re: How do I get the gun finish back on my SP101 cylinder?
Not enough contrast on the pix. Could just be on the surface and needs a good cleaning. That's my guess at this point unless you can post better pix.
Welcome to the site.My Feedback - http://forum.pafoa.org/showthread.ph...ight=stainless
-
November 16th, 2016, 03:32 PM #4
Re: How do I get the gun finish back on my SP101 cylinder?
If it's chambered in .327 Federal, sell it to me; then it's not YOUR SP101 anymore and you don't need to worry about the finish. Problem solved.
Soap Box - Worn out : Ballot Box - Broken : Jury Box - Pending : Ammunition Box - Unknown
-
November 16th, 2016, 03:43 PM #5
Re: How do I get the gun finish back on my SP101 cylinder?
Id give it a generous drink of WD 40, amazing stuff
-
November 16th, 2016, 04:41 PM #6
-
November 23rd, 2016, 08:28 AM #7Member
- Join Date
- Nov 2016
- Location
-
Lansdale,
Pennsylvania
(Montgomery County) - Posts
- 33
- Rep Power
- 0
Re: How do I get the gun finish back on my SP101 cylinder?
Hello all,
Sorry for the late response but work, kids, and wife got the best of me the last several days.
I tried the WD40 with Hoppe's with no luck ��. Next step is going over to see my smith to see about bluing.
Thank you all your help!
-
November 23rd, 2016, 09:54 AM #8
Re: How do I get the gun finish back on my SP101 cylinder?
Use kroil or pbblaster ,wd40 is not intended for firearm use as it's a water dissipator and can dull the finish over time. It can be used to clean something up but you always need to follow with a gun oil such as kroil, clp, rem oil or whatnot after. Pb blaster is a good choice if no kroil is available and can be bought at lowes ect.
-
November 30th, 2016, 07:02 PM #9
Re: How do I get the gun finish back on my SP101 cylinder?
What ammo did you shoot when this happened?
Some people just plain suck.
If you're gonna be dumb ya gotta be tough.
-
November 30th, 2016, 09:30 PM #10
Re: How do I get the gun finish back on my SP101 cylinder?
You didn't use a lead removal cloth on that did you? They remove blue. Keeping NIB look but shooting gun are two incompatible things. Efforts to remove signs of use often result in loss of finish and outright damage. Getting your gun reblued every time you shoot it isn't realistic. Clean with good bore solvent and 100% cotton patch, wipe down with a good gun oil.
Similar Threads
-
To finish or not to finish? Opinions
By dteed4094 in forum RiflesReplies: 2Last Post: August 16th, 2010, 08:43 PM -
Got my SP101 back :)
By JoeWilliams in forum GeneralReplies: 8Last Post: July 6th, 2009, 10:03 PM -
Ruger Sp101 2 1/4 in. for Sp101 with 3 1/8 barrel
By allglock in forum GeneralReplies: 0Last Post: November 28th, 2008, 07:27 PM
Bookmarks