Results 1 to 10 of 21
Thread: Small rattle with Beretta 92FS
-
March 15th, 2016, 11:06 PM #1Super Member
- Join Date
- Jun 2012
- Location
-
Honesdale,
Pennsylvania
(Wayne County) - Posts
- 693
- Rep Power
- 2990182
Small rattle with Beretta 92FS
hey, I have a question about my Beretta 92FS. This is my first pistol so I'm still learning about it. I field stripped it, cleaned, and reassembled it a few times no problem. Here's the thing, when I shake the gun I can hear something rattling slightly inside. It sounds like a small metal pin is hitting against the frame or something, it's not loud just a slight noise. Is this normal?
-
March 16th, 2016, 08:44 AM #2
Re: Small rattle with Beretta 92FS
Is that with or without the mag inserted?
I'm only here for the wood c-rings.
-
March 16th, 2016, 08:50 AM #3
-
March 16th, 2016, 04:33 PM #4Senior Member
- Join Date
- Feb 2013
- Location
-
Pittsburgh,
Pennsylvania
(Allegheny County) - Posts
- 472
- Rep Power
- 1692383
Re: Small rattle with Beretta 92FS
without inspecting the gun it is hard to say if anything is normal, but yeah, could be normal...the fit-up would be fairly loose on any service gun and could have a little rattle...
-
March 16th, 2016, 04:36 PM #5
Re: Small rattle with Beretta 92FS
Look for something like this:
NoahWisdom and knowledge shall be the stability of thy times.
-
March 16th, 2016, 05:08 PM #6Banned
- Join Date
- Dec 2012
- Location
-
The land o' cotton, old times there are not forgotten
- Posts
- 3,536
- Rep Power
- 0
Re: Small rattle with Beretta 92FS
It's been my experience with Beretta's that they don't fit the Knuder pin as tightly as possible. This allows for slightly higher reliability at the cost of a small rattle.
-
March 16th, 2016, 06:16 PM #7
Re: Small rattle with Beretta 92FS
My M9 is tight with the slide in battery and no mag inserted.
-
March 16th, 2016, 08:03 PM #8Super Member
- Join Date
- Jun 2012
- Location
-
Honesdale,
Pennsylvania
(Wayne County) - Posts
- 693
- Rep Power
- 2990182
-
March 18th, 2016, 10:46 PM #9Super Member
- Join Date
- Jun 2012
- Location
-
Honesdale,
Pennsylvania
(Wayne County) - Posts
- 693
- Rep Power
- 2990182
Re: Small rattle with Beretta 92FS
i just stripped, reassembled the gun, i dont hear anything, weird. im going to the range tomorrow to shoot it and see what happens
-
March 19th, 2016, 12:22 AM #10Banned
- Join Date
- Dec 2012
- Location
-
The land o' cotton, old times there are not forgotten
- Posts
- 3,536
- Rep Power
- 0
Re: Small rattle with Beretta 92FS
Did you tighten the Knuder pin?
Similar Threads
-
BERETTA 92FS
By RUDY850 in forum GeneralReplies: 7Last Post: October 30th, 2009, 03:28 PM -
Beretta 92FS Inox for a Blued Italian 92FS or a Sig in 9mm
By nittanylion4ever in forum GeneralReplies: 1Last Post: October 22nd, 2009, 02:10 PM
Bookmarks