Results 1 to 10 of 18
-
August 10th, 2015, 08:58 AM #1
Painting revolver front post (Updated w/ pics)
I just acquired a new Taurus 85, steel frame, "blued" revolver. I love it thus far, but I want to paint the front post serrations to make aiming easier.
Anyways, should I use model paint or nail polish? I'm going to try white first. I think that will be the easiest for me to aim with. If not, I'm going to paint blaze orange over the white.
If I go the nail polish route, any brand recommendations? I don't want it to look cheap. Also I know to clean the front sight using rubbing alcohol first.
Thanks!
Edit: See post #15 for picsLast edited by philadelphia patriot; August 11th, 2015 at 05:33 PM.
"The Constitution is the guide which I will not abandon.” - George Washington
-
August 10th, 2015, 09:01 AM #2
Re: Painting revolver front post
Montani Semper Liberi
-
August 10th, 2015, 09:25 AM #3
-
August 10th, 2015, 09:33 AM #4
Re: Painting revolver front post
I used orange modeling paint on two of my revolvers. It seems to be holding up quite well.
Navy ⚓️ 1965–1969
-
August 10th, 2015, 09:37 AM #5
-
August 10th, 2015, 10:14 AM #6
Re: Painting revolver front post
I use off-white / almond appliance touch-up paint. It is solvent-borne and cures very hard. Clean with acetone and a Q-tip first.
http://www.amazon.com/Sheffield-1438...paint+touch+up
NoahWisdom and knowledge shall be the stability of thy times.
-
August 10th, 2015, 10:17 AM #7
Re: Painting revolver front post
I've used red, orange or white nail polish in the past. Works great, holds up really well and whenever you decide you're done with it just wipe it off with some nail polish remover.
--Adam
-
August 10th, 2015, 11:02 AM #8
Re: Painting revolver front post
Thank you all for your input. I think I'm going to try the off white first then the blaze orange if I need some color.
Aside from that, I'm very impressed with my $240 taurus 85. It's even the new model with the matte black finish and rubber bull grips."The Constitution is the guide which I will not abandon.” - George Washington
-
August 10th, 2015, 05:28 PM #9
Re: Painting revolver front post
Noah's stuff sounds very good. I especially like his degreaser! Just be sure you don't use the "oily nail polisher remover" get the stuff that says 100% acetone!
Also if you want really long lasting stuff take a look at CS Coatings Jig and Lure Paint! The stuff seems to last forever! The downside is cost and you must buy the white and the special solvent in addition to your choice of final color, the white is used as a primer, undercoat.
You might even consider Testors' model airplane enamel.
"Those who can make you believe absurdities can make you commit atrocities".
-
August 10th, 2015, 05:53 PM #10
Re: Painting revolver front post
I'm going to post pics when I am done (probably later this week). I picked up "vintage white" and "pure orange" multi-surface satin acrylic paint. I cleaned the area with a 91% rubbing alcohol soaked Q-tip. I just put my 2nd coat of vintage white on. I'm going to put on one more coat of vintage white later tonight, and tomorrow I am going to put on 2-3 coats of pure orange. Just painting the serrations white has helped aiming [while dry firing] a lot easier. After the coats of pure orange dry, then I'm going to put some nail polish sealer on it, and it should be good to go!
Thank you for everybody's advice! Again I'll post pics of the final results once everything is done and dry."The Constitution is the guide which I will not abandon.” - George Washington
Similar Threads
-
Where can I buy a pinned in front sight for a S&W revolver?
By bripro in forum GunsmithingReplies: 3Last Post: November 23rd, 2014, 08:52 PM -
thoughts on painting front sight post.
By messeduprex in forum RiflesReplies: 11Last Post: March 23rd, 2013, 01:02 PM -
Painting a front sight-
By Plain Old Bill in forum GunsmithingReplies: 10Last Post: September 28th, 2010, 06:48 PM
Bookmarks