Results 1 to 10 of 14
Thread: Glock 21 Gen 4 Failure to feed
-
June 10th, 2015, 07:07 PM #1Banned
- Join Date
- Mar 2015
- Location
-
Hanover,
Pennsylvania
- Posts
- 32
- Rep Power
- 0
Glock 21 Gen 4 Failure to feed
Have an issue with the above gun. Seems like the slide gets "stuck" when pulling back the slide. Almost as if the slide release engages even though there are rounds in the magazine. The rounds dont even get pushed out of the magazine. Anyone have a problem like this?
-
June 10th, 2015, 07:08 PM #2Banned
- Join Date
- Mar 2015
- Location
-
Hanover,
Pennsylvania
- Posts
- 32
- Rep Power
- 0
Re: Glock 21 Gen 4 Failure to feed
Also I am using factory federal ammo and the provided Glock 13 rd mags
-
June 10th, 2015, 07:32 PM #3Grand Member
- Join Date
- Dec 2010
- Location
-
back to Port Charlotte,
Florida
- Age
- 60
- Posts
- 5,483
- Rep Power
- 3627622
Re: Glock 21 Gen 4 Failure to feed
Last edited by harold63; June 10th, 2015 at 07:57 PM.
BCM and Glock...for a bigger pile of 'cold dead hands' brass.
-
June 10th, 2015, 07:40 PM #4Grand Member
- Join Date
- Aug 2011
- Location
-
Moscow,
Pennsylvania
(Lackawanna County) - Posts
- 4,029
- Rep Power
- 21474853
Re: Glock 21 Gen 4 Failure to feed
is the spring for the slide stop under the pin for the locking block?
-
June 10th, 2015, 09:34 PM #5Banned
- Join Date
- Mar 2015
- Location
-
Hanover,
Pennsylvania
- Posts
- 32
- Rep Power
- 0
-
June 10th, 2015, 09:35 PM #6Banned
- Join Date
- Mar 2015
- Location
-
Hanover,
Pennsylvania
- Posts
- 32
- Rep Power
- 0
Re: Glock 21 Gen 4 Failure to feed
[QUOTE=NathanB;3070027]is the spring for the slide stop under the pin for the locking
Yes
-
June 10th, 2015, 10:11 PM #7Grand Member
- Join Date
- Dec 2010
- Location
-
back to Port Charlotte,
Florida
- Age
- 60
- Posts
- 5,483
- Rep Power
- 3627622
Re: Glock 21 Gen 4 Failure to feed
Can you see if the slide stop lever is actually being pushed up into the notch on the slide when you pull the slide back? Also, with the slide off the frame, pick up on the slide stop lever and see if it snaps back down. If it doesn't your spring may be to blame. A new slide stop lever and spring is cheap...about $11. Also look to see if the ammo is tagging the slide stop lever from the inside. Without seeing it, it's hard to know. Does is do it with the other mags?
BCM and Glock...for a bigger pile of 'cold dead hands' brass.
-
June 10th, 2015, 10:59 PM #8Senior Member
- Join Date
- Feb 2013
- Location
-
North Wales,
Pennsylvania
(Montgomery County) - Posts
- 292
- Rep Power
- 1393004
Re: Glock 21 Gen 4 Failure to feed
I had a problem with the ammo failing to eject with my Nano. I also was using federal 115 grain ammo. I had heard that the Nano was designed for cartridges more powerful than 115 grain. I went through 100 rounds using PMC 115 grain ammo and had no problem. I think you should try different ammo or a more powerful cartridge.
-
June 11th, 2015, 01:40 PM #9Banned
- Join Date
- Mar 2015
- Location
-
Hanover,
Pennsylvania
- Posts
- 32
- Rep Power
- 0
Re: Glock 21 Gen 4 Failure to feed
Think I got it fixed, disassembled and reassembled and it is working. I bent out the spring a little bit on the slide release lever.
-
June 11th, 2015, 05:32 PM #10Grand Member
- Join Date
- Dec 2010
- Location
-
back to Port Charlotte,
Florida
- Age
- 60
- Posts
- 5,483
- Rep Power
- 3627622
Re: Glock 21 Gen 4 Failure to feed
BCM and Glock...for a bigger pile of 'cold dead hands' brass.
Similar Threads
-
Sig 1911 RCS Failure-To-Feed
By MMH in forum PistolsReplies: 17Last Post: April 4th, 2015, 10:27 AM -
Failure to feed question?
By nailer in forum PistolsReplies: 4Last Post: April 14th, 2012, 06:32 PM -
Can someone tell me what could cause this failure to feed?
By Quantum62 in forum PistolsReplies: 22Last Post: December 27th, 2010, 08:35 PM -
Failure to feed on HK USP Compact....help?
By SierraPapa in forum PistolsReplies: 16Last Post: March 29th, 2010, 02:56 AM -
H&K P2000 Feed Failure
By emsjeep in forum GeneralReplies: 5Last Post: September 21st, 2008, 11:04 PM
Bookmarks