Pennsylvania Firearm Owners Association

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.
Welcome to the Pennsylvania Firearm Owners Association Forum, we hope you like what you find here and we strongly encourage you to register for an account with us, especially if you are from Pennsylvania. Once registered you will have access to participate in our community. Thanks for visiting and we hope you become a regular!
Attention! There has been an influx of scammer signups!

The method of operation is to private message you and tell you that you should contact such 'n such person at a given email address.

Please report the private messages. Staff will ban the offender, and I will implement an IP ban. Unfortunately these scammers are using VPN/proxy services, which may mean your VPN/proxy may be blocked.
Attention! About VPN's and foreign IP addresses.

When signing up, do so from a US based Internet Service Provider. Turn off any VPN/safe-browsing feature. Failure to do so will result with your new account denied.

If you run into a IP ban afterwards as a member, again - turn off your VPN or switch servers. We do not ban legit Internet Service Providers from the USA(exception for certain individual IP addresses). Free VPN's tend to get banned too. We try not to ban legit subscription VPN services, but they rarely label their IP blocks correctly.

If you run into an IP ban, it likely wasn't you.

Results 1 to 2 of 2

Thread: cutting front sight dovetail in .22 rifle

Thread Tools
Display
- Linear Mode
- Switch to Hybrid Mode
- Switch to Threaded Mode

October 20th, 2013, 09:22 PM #1
93-2.3

View Profile

View Forum Posts

Private Message

Super Member
Join Date

May 2008

Location

Whitehall, Pennsylvania
(Lehigh County)

Posts

583

Rep Power

73616
cutting front sight dovetail in .22 rifle

I have an old beater .22 that I wanna shorten the barrel on to like 16.5 or 17 inches was wondering if anyone in or close to lehigh county has the jig to cut the sight dovetail into the barrel that would be willing to help me out.

A.T.F alcohol, tabacco, and firearms... who's bringing the chips?

Reply With Quote
October 22nd, 2013, 03:50 PM #2
Urban_Redneck

View Profile

View Forum Posts

Private Message

Senior Member
Join Date

Mar 2012

Location

Monroe County
(Monroe County)

Posts

261

Rep Power

379506
Re: cutting front sight dovetail in .22 rifle

all you need: http://www.brownells.com/gunsmith-to...s-prod698.aspx

Reply With Quote

Quick Navigation Gunsmithing Top

Site Areas
Settings
Private Messages
Subscriptions
Who's Online
Search Forums
Forums Home
Forums
Forum
Discussion
Law & Politics
1. Pennsylvania
2. National
Marketplace
Events
Private Forums
1. PAFOA Club
Regions
1. Lake Erie Region
  1. Crawford
  2. Erie
  3. Mercer
  4. Venango
2. Allegheny National Forest Region
  1. Cameron
  2. Clarion
  3. Clearfield
  4. Elk
  5. Forest
  6. Jefferson
  7. McKean
  8. Potter
  9. Tioga
  10. Warren
3. Valleys of the Susquehanna Region
  1. Centre
  2. Clinton
  3. Columbia
  4. Juniata
  5. Lycoming
  6. Mifflin
  7. Montour
  8. Northumberland
  9. Snyder
  10. Union
4. Pocono Mountain Region
  1. Bradford
  2. Carbon
  3. Lackawanna
  4. Luzerne
  5. Monroe
  6. Pike
  7. Schuylkill
  8. Sullivan
  9. Susquehanna
  10. Wayne
  11. Wyoming
5. Lehigh Valley & Philadelphia Region
  1. Bucks
  2. Chester
  3. Delaware
  4. Lehigh
  5. Montgomery
  6. Northampton
  7. Philadelphia
6. PA Dutch Country/Hershey Region
  1. Adams
  2. Berks
  3. Cumberland
  4. Dauphin
  5. Franklin
  6. Lancaster
  7. Lebanon
  8. Perry
  9. York
7. Laurel Highlands Region
  1. Bedford
  2. Blair
  3. Cambria
  4. Fayette
  5. Fulton
  6. Greene
  7. Huntingdon
  8. Indiana
  9. Somerset
  10. Westmoreland
8. Pittsburgh Region
  1. Allegheny
  2. Armstrong
  3. Beaver
  4. Butler
  5. Lawrence
  6. Washington
Miscellaneous
1. The Lounge

« Previous Thread | Next Thread »

Similar Threads

Low Mount Sight Dovetail Cutters - 1911

By WWGunslinger in forum Gunsmithing

Replies: 5
Last Post: April 21st, 2013, 10:20 AM
Replacing rear dovetail sight on Makarov Snyder County area

By em2b96p in forum Gunsmithing

Replies: 3
Last Post: October 12th, 2012, 06:25 PM
Mosin Nagant 91/30 Rear Sight Dovetail Size?

By tractorfarmer in forum Rifles

Replies: 10
Last Post: September 19th, 2012, 10:08 AM
Dovetail Sight Pusher Recommendations

By Steve_NEPhila in forum General

Replies: 5
Last Post: November 6th, 2009, 09:36 PM