Results 1 to 10 of 100
Thread: 585 HE -- Cases In Production --
Hybrid View
-
October 9th, 2013, 01:44 AM #1Active Member
- Join Date
- Jun 2009
- Location
-
Brinton,
Michigan
- Posts
- 185
- Rep Power
- 504413
585 HE -- Cases In Production --
585 HE --- Tested Super Strong --
If you've followed our work in the 12ga FH thread you've seen
our 585 HE cartridge and its development. We have barrels
of cases and more coming.
We have put it in all kinds of guns, and tested it with 650gr
bullet over 3000 fps as heavy load to test the brass, and also
for lighter game like deer and hogs and target fun we found
that some of 440gr- 540gr 58cal Minie bullets work great
First picture shows it next to 505 Gibbs, it has same overall
loaded length as a Gibbs. Holds up to 190gr ball powder.
Next pic is a barrel of cases
Third representative of types of guns we have it in.Ed
.
.
.Last edited by hubel458; October 10th, 2013 at 02:29 AM.
-
October 13th, 2013, 01:29 AM #2Active Member
- Join Date
- Jun 2009
- Location
-
Brinton,
Michigan
- Posts
- 185
- Rep Power
- 504413
Re: 585 HE -- Cases In Production --
We get asked about recoil. Guns are weighted a little, thick pads,
can be ported, use moderate loads, they shoot nice...And moderate
loads still much faster than 577NE. And can be had without costing a
years pay. Most local users(only 1 in 10000 hunters go Africa) can
shoot lighter .585 Minie bullets, which load for about 95 cents each,
once you have cases. Great for target fun, hogs, deer, etc... Cases
last forever. We can load to any power level we need or want.
Folks can get 100 cases, dies, barrel to put in something, 750 bucks.
Asked about #1, And perfect case for the Ruger #1.
The few #1s ever done in 577, they had to relieve
metal behind the action shoulders that breach block
rests against because of rim. Ours don't have to and the #1s
extractors I've seen work better with belted than big rimmed.
Ours holds more powder, cases built for extreme pressures.Ed
-
October 25th, 2013, 02:18 PM #3Active Member
- Join Date
- Jun 2009
- Location
-
Brinton,
Michigan
- Posts
- 185
- Rep Power
- 504413
Re: 585 HE -- Cases In Production --
Case doesn't need special made shellholder, number 31 RCBS fits fine.
It is a straight belted case that holds up to 190gr of doublebase powder.
Powder need not be like charcoal, IE, really slow powder, as necked
needs. So it has effiencies of 37-39%, where necked cases are
about 29%. Here is one done in a Savage..
The loads tested at high pressures about 65,000 psi, when extracting, the
weight of the bolt after opening pulled cases out. We've fired moderate
loads in singleshots that we mono-blocked barrels into and the cases fall
out after firing. Here are couple a nice singles with 585HE in them.
Cases are made super strong, in the same factory run as the super
high pressure Cheytac cases. The base of our case is same size ahead of
belt as Cheytac/Gibbs bases. Done with same cups and draws, just uses
a different header, bunter, and sizer. Here is picture of the one we made
and the factory one sectioned showing the strong built inside corners.
These are not balloon head junk cases.
We and CH4D have die sets, Manson makes reamers, and we have some.
Reamer specs all set and the chambers made with them, the cases
extract at the highest pressures.
Here is pic of one we set with 585HE in a Greener GP.Ed
-
October 29th, 2013, 12:16 PM #4Active Member
- Join Date
- Jun 2009
- Location
-
Brinton,
Michigan
- Posts
- 185
- Rep Power
- 504413
Re: 585 HE -- Cases In Production --
WE get asked about whether the 585HE is a DD due to being
over 50 cal, and no it is not, as we applied for and got a
sporting cartridge exemption few years ago.
First picture is base view of cases new and old. On the left is
4 new ones that come with no headstamp that I stamped,
and the 6 new ones in the middle has a 585 stamp.
We got a barrel full without stamp and guys can wildcat
them and put their own stamp on..
Second is side view with some in # 31 holders.No special
holders needed. .Notice how uniform belts are on the new
shiny ones. Dark ones are ones I made years ago.
Third is one with AP bore rider bullet in with others
behind. Maybe make a great long range target cartridge.
Got a guy setting up one with long heavy barrel for that.
Here is picture of 585HE with 700gr HP CEB bullet and 750 gr
wide meplat CEB bullet..Ed
-
October 29th, 2013, 01:25 PM #5
Re: 585 HE -- Cases In Production --
You're crazy. And I approve
-
November 8th, 2013, 03:27 AM #6Active Member
- Join Date
- Jun 2009
- Location
-
Brinton,
Michigan
- Posts
- 185
- Rep Power
- 504413
Re: 585 HE -- Cases In Production --
In the pictures above you see the older first cases I made from Nyati
cases and other cases that were Nyati clones. These were straight basic,
long, untrimed cases, so I could get the longer case we wanted.
We get asked about the process of doing it and here is picture sketch
showing original case, a case with the start of a belt step, and finally
a case after it is swaged and sized. Note the belt diameter ends up the
same as the base diameter of the original brass. These cases we made
years ago was how we got the 585HE started and tested and some guns
done. This process can only work with original cases that have a thick
corner radius to leave plenty of thickness ahead of the belt. In doing this
process with different wildcats we have found cases that wouldn't work.
Now these cases have a diameter that works with regular bolt guns,
without extreme machining on the bolt, as opposed to 577NE and Trex.
Here is picture of a case held in a Ruger bolt, for example..
And our case is large enough capacity to get the power, without being an
oversize, soft case. Thicksided cases relative to size of the case are much
harder to harden the heads and the lower body back up to proper strength.
because of the extreme annealling needed, in the drawing
and heading operations in the manufacturing process.
Our cases are made with same cups and draws as the ultra high pressure
Cheytac cases, and our real high pressure tests show they perform with
no extraction problems.
Here is picture of a O/U I had top barrel sleeved with smooth tube, and use
the 585HE in it with lightweight, hollowbase Minie bullets. Shoots about as
accurate as foster slugs in a 12ga. Bottom barrel is 3.5" 12ga smooth.
-
August 1st, 2017, 11:19 AM #7Banned
- Join Date
- Jun 2017
- Location
-
Phoenix,
Arizona
- Posts
- 250
- Rep Power
- 0
Re: 585 HE -- Cases In Production --
I could build a AR varient that could shoot that. Interesting!!!!
-
September 4th, 2017, 11:14 PM #8Active Member
- Join Date
- Jun 2009
- Location
-
Brinton,
Michigan
- Posts
- 185
- Rep Power
- 504413
Re: 585 HE -- Cases In Production --
Here is case measurements for our 416 HE target case
made by necking our 585 HE big belted case.
Here is picture of 375 HE left, 416 HE next, 416 HSM on the right..
Here, tentative specs, 416 HSM case we are doing from bmg brass,
A 375 HE, with Lawton action, few are being done with those,Ed .....
-
October 9th, 2017, 05:44 PM #9Active Member
- Join Date
- Jun 2009
- Location
-
Brinton,
Michigan
- Posts
- 185
- Rep Power
- 504413
Re: 585 HE -- Cases In Production --
A 585 HE ...shot with moderate heavy load......
https://scontent.cdninstagram.com/t5...09533184_n.mp4
Here is a 375 HE target gun set up, by Asteroid Precision...
Here is video of it being tested... And with a 350gr bullet about 3450-3475,
bolt opened easily with one finger...And he's just getting started
and is checking on better powder, Ed..
https://www.facebook.com/AsteroidPre...location=group
-
November 11th, 2017, 01:16 AM #10Active Member
- Join Date
- Jun 2009
- Location
-
Brinton,
Michigan
- Posts
- 185
- Rep Power
- 504413
Re: 585 HE -- Cases In Production --
Here is recap simple setup to get faster loads with 12ga sabots
& slugs, Example using break actions...., reaming chamber
in a 12ga break action to 3.5" with a 3.5" 12ga reamer, that isn't
something needing special order, and use 3.5" plastic cases , or
get 3.5" brass cases made. With mag shotgun primers and
our slower powder loads you can get a quarter more speed,
which gives 50% more energy...
585 Hubel Express video, 190ft/lbs recoil, heavy load, gun little light.....
https://www.youtube.com/watch?v=tyS9zZ8ElJA
Another view of Asteroid Precision's.... 375 HE target gun,
Here is our 416 HSM we are developing next to 416 Barrett, Ed
Similar Threads
-
Marking cases
By WVneighbor in forum Ammunition & ReloadingReplies: 18Last Post: February 21st, 2013, 10:52 PM -
Bent 40s&w cases
By originalsocko in forum Ammunition & ReloadingReplies: 6Last Post: January 2nd, 2011, 12:18 PM
Bookmarks