Results 1 to 10 of 21
Thread: Bore Snakes
-
March 5th, 2013, 03:25 PM #1
Bore Snakes
Okay, newbie here as many new. I am trying the Frog Lube route, regardless, I bought two bore snakes (9mm, 22LR). I am wondering how they fit in my maintenance routine? After shooting at the range and before I get a chance to do a good wipe down and clean? During my cleaning? Do I apply Frog Lube to it as part of cleaning? How does one clean a bore snake?
Just curious.Gunowner99 - NRA Benefactor Life Member
-
March 5th, 2013, 03:48 PM #2
Re: Bore Snakes
I use my bore snakes as a replacement for a cleaning rod for the bore. I use Break Free on the bore while dirty, run the broe snake through and presto!
I have never cleaned a boresnake, I threw one out when it was frayed terribly. The big advantage to a bore snake is that it does not run the risk of dinging up the crown of the muzzle, which can happen in rifles. I am a proponent of bore snakes, they smiplify cleaning the bore and prevent damage.Join the groups protecting your rights from the fools trying to take them from you!
-
March 5th, 2013, 03:59 PM #3
Re: Bore Snakes
I love bore snakes. Saves time and prevents accidental damage as the previous poster noted. Some people have had them break causing them to get stuck in the bore, so do be careful and don't buy the cheap chinese knock-offs. Yes, I'm sure this happens to the Hoppes snakes as well, but I have no problem spending an extra 2 dollars for a known brand.
As far as cleaning them goes, I put mine in an empty water bottle along with some Tide or dish soap, fill it half way or so, and shake that thang. Then, let it sit for a few hours to let most of the dirt settle. Then, pull it (or them if you wash a couple) out with a hook tool of some type so you don't disturb the dirty water too much. After it's out, thoroughly rinse it or them, then hang dry. Done!You can never have enough horsepower or ammunition.
-
March 5th, 2013, 04:01 PM #4Grand Member
- Join Date
- Dec 2010
- Location
-
back to Port Charlotte,
Florida
- Age
- 60
- Posts
- 5,483
- Rep Power
- 3627622
Re: Bore Snakes
I clean mine with dish soap. Rinse by wetting a few time and running it through squeezed together fingers. Works great. Don't forget to let a little pressure off when the brass gets to your fingers. For rifles they are great. Kinda pointless on a handgun, IMO, but usable, none the less.
BCM and Glock...for a bigger pile of 'cold dead hands' brass.
-
March 5th, 2013, 06:24 PM #5Active Member
- Join Date
- Apr 2008
- Location
-
Bethlehem,
Pennsylvania
(Northampton County) - Posts
- 220
- Rep Power
- 2584221
Re: Bore Snakes
As far as cleaning goes: As per the instructions that came with my Bore Snakes, it said to place them in an old sock ans throw them in the washing machine. I've tried it several times and it works well for me.
Smit
-
March 5th, 2013, 06:43 PM #6Active Member
- Join Date
- Jan 2012
- Location
-
Spring City, PA,
Pennsylvania
(Chester County) - Posts
- 220
- Rep Power
- 1237
Re: Bore Snakes
I have three bore snakes, one for each gun. The handgun bore snakes are much shorter than the rifle ones and I think still make a ton of sense, for the same reason that they do for rifles.
I also haven't cleaned any of mine yet...none of them seems dirty at all.
I do tend to put a few drops of CLP on the forward-most part of the snake (where the black string meets the patterned, thicker part), on the brushes, and just at the end. I figure this would help coat the barrel while I run it through a couple of times to help clean it up nicely. All three of my barrels look brand spankin' new right now.
Also, on them potentially breaking...I don't have a barrel longer than 20", but I feel like if at any point it breaks, there's more than enough sticking out the other end that it could just be pulled right back out.
-
March 5th, 2013, 07:38 PM #7Grand Member
- Join Date
- Dec 2010
- Location
-
back to Port Charlotte,
Florida
- Age
- 60
- Posts
- 5,483
- Rep Power
- 3627622
Re: Bore Snakes
Here's how much I know about cleaning guns the gun way...I didn't even know they made them for handguns. I only have two of them. One fits a .22 cal and the other a 30 cal. Probably get a .33 cal soon as I shoot it enough. I saw they got cables to pull your brushes and what not through your bores, but I made some of them years ago.
Last edited by harold63; March 5th, 2013 at 07:46 PM.
BCM and Glock...for a bigger pile of 'cold dead hands' brass.
-
March 5th, 2013, 07:51 PM #8
-
March 6th, 2013, 02:46 PM #9Member
- Join Date
- Mar 2012
- Location
-
Lancaster,
Pennsylvania
(Lancaster County) - Posts
- 66
- Rep Power
- 8043
Re: Bore Snakes
boresnakes are garbage, if you actually want your gun to get clean use a rod and jag
-
March 6th, 2013, 02:50 PM #10
Similar Threads
-
Avoid Hoppes .22 bore-snakes (and Bushnell products in general)
By gascolator in forum GeneralReplies: 36Last Post: October 18th, 2012, 02:15 PM -
Bore Snakes - Talk About Slicker Than Snot On A Door Knob!
By dc dalton in forum GeneralReplies: 40Last Post: March 15th, 2010, 07:11 AM -
Bore Snakes
By Guns4Fun in forum GeneralReplies: 17Last Post: March 3rd, 2009, 12:12 PM -
Hoppes Bore Snakes .223 & .30cal
By Jay5oh in forum GeneralReplies: 4Last Post: March 1st, 2007, 10:12 PM
Bookmarks