Results 1 to 7 of 7
-
March 4th, 2013, 02:21 PM #1Junior Member
- Join Date
- Jan 2013
- Location
-
Western
- Posts
- 19
- Rep Power
- 0
Glock 17 19 26 Gen 3 magazines vs Gen 4 compatibility.
Hi.
Its my understanding that the Generation 3 Glock 17 and 19 magazines would fit a Glock 26.
Assuming that this is correct, would say a Generation 4 Glock 17 magazine fit a Generation 3 Glock 26?
Hope I have asked this in a clear enough manner.
Thank you.
May have been simpler to ask if the Generation 3 and Generation 4 magazines for the Glocks 17 19 and 26 are interchangeable.
-
March 4th, 2013, 02:24 PM #2
Re: Glock 17 19 26 Gen 3 magazines vs Gen 4 compatibility.
Gen 3 or 4 9mm mags of any capacity work in any gen 3 9mm glock from my experience. I have a factory 33 rounder that has the ambi cuts and it works fine in my gen 3 G19 for example.
In fact IIRC the only problems you can run into with mag compatibility is if you have a Gen4 Glock with the mag release swapped to left hand control. Then you need a Gen 4 mag with the ambi cuts.Last edited by Splittiebus66; March 4th, 2013 at 02:29 PM.
I always sleep with my guns when you are gone
-
March 4th, 2013, 03:02 PM #3
Re: Glock 17 19 26 Gen 3 magazines vs Gen 4 compatibility.
This is correct. Gen 4 mags have a cut on the other side of the mag so if the mag release is swapped the mag will still work. As long as the mag is the same or larger capacity as the original it will work in that gun. You can't, however, use a smaller capacity mag in a gun because it will be too short. IE: A Glock 17 mag will work in a Glock 26, but not the other way around.
-
March 4th, 2013, 04:28 PM #4
Re: Glock 17 19 26 Gen 3 magazines vs Gen 4 compatibility.
Yep. Can use previous gens in a 4. But was told cannot use the gen 4 mags in an older glock.
-
March 4th, 2013, 05:45 PM #5Member
- Join Date
- Jul 2009
- Location
-
Altoona,
Pennsylvania
(Blair County) - Posts
- 45
- Rep Power
- 0
Re: Glock 17 19 26 Gen 3 magazines vs Gen 4 compatibility.
-
March 4th, 2013, 06:21 PM #6
-
March 4th, 2013, 07:23 PM #7
Similar Threads
-
CZ 75 slide compatibility
By S&W M&P40c in forum PistolsReplies: 0Last Post: December 11th, 2011, 10:57 AM -
Kel Tec Sub2000 grip compatibility question
By Valorius in forum RiflesReplies: 3Last Post: September 21st, 2011, 05:19 PM -
charles daly compatibility with after market kits
By lance4682 in forum GeneralReplies: 0Last Post: October 8th, 2009, 09:23 PM -
Ruger MKII/III grip panel compatibility?
By Cheeseybacon in forum GeneralReplies: 8Last Post: April 16th, 2008, 09:09 PM -
hearing protection and MP3 player compatibility
By Atomic Dog in forum GeneralReplies: 8Last Post: December 8th, 2007, 02:35 PM
Bookmarks