Results 1 to 8 of 8
Thread: new 10/22 mods
-
November 15th, 2012, 05:16 PM #1Junior Member
- Join Date
- Sep 2012
- Location
-
Lititz,
Pennsylvania
(Lancaster County) - Posts
- 25
- Rep Power
- 0
new 10/22 mods
I got these mods for my 10/22 i was told they are easy to install. Just wanted to see what you guys thought and if you had any tips
Thanks
Volquartsen Exact Edge Extractor
Volquartsen Automatic Bolt Release
Volquartsen Exact Edge Extractor
-
November 15th, 2012, 06:46 PM #2
Re: new 10/22 mods
My husband installed the extractor in one of our 10/22s and it greatly improved the stovepipes. I have the bolt release part also but haven't installed that one yet. We also installed the bolt buffer. (i forget if that is the right wording)
You mentioned one twice! did you mean the mag release also? I didn't get that part yet.
-
November 15th, 2012, 07:59 PM #3
Re: new 10/22 mods
Should be fairly easy to install. I've replaced most of the trigger group for mine. VQ hammer and sear, bolt hold open dohickey, extended mag release, and more...
Μολὼν λάβε
-
November 15th, 2012, 09:14 PM #4
Re: new 10/22 mods
The 10/22 is easy to work on and the parts should have come with instructions to get it installed.
Ron USAF Ret E-8 FFL01/SOT3 NRA Benefactor Member
-
November 15th, 2012, 09:21 PM #5Senior Member
- Join Date
- Dec 2008
- Location
-
NEPA,
Pennsylvania
(Wayne County) - Posts
- 286
- Rep Power
- 10937
Re: new 10/22 mods
"Freedom is our most precious commodity and if we are not eternally vigilant, government will take it all away. Individual freedom demands individual responsibility."
-
November 15th, 2012, 10:01 PM #6Junior Member
- Join Date
- Sep 2012
- Location
-
Lititz,
Pennsylvania
(Lancaster County) - Posts
- 25
- Rep Power
- 0
Re: new 10/22 mods
I just got done watching some videos it does look pretty easy thanks
-
December 23rd, 2012, 09:30 PM #7Junior Member
- Join Date
- Mar 2012
- Location
-
Perkasie,
Pennsylvania
(Bucks County) - Posts
- 22
- Rep Power
- 0
Re: new 10/22 mods
I just purchased a used 10/22 with a folding stock RAM-Line stock. Some mods were ready done. The trigger was the hardest part keeping it and the spring align. I'm going to make a short pin to assemble it then push the full pin in once the trigger is in the housing. I modified my bolt release plate instead of buying a new one. I found it doesn't like hollow point, ammo FTF issues. I'm not a gunsmith but I love to disassemble my guns then reassemble. Polishing parts like the bloggers on YouTube show you.
Donald A. Jones
-
December 30th, 2012, 10:19 PM #8
Re: new 10/22 mods
A cue tip works in a pinch, just cut it to the right length.
To the OP, The bolt release is easy, although if you wanted to be thrifty, you can make the stock Ruger release work the same as the Volq one.
I made a thread a while back about mods to the 10/22, check it out:
http://forum.pafoa.org/gunsmithing-4...r-10-22-a.htmlThe smallest minority on earth is the individual. Those who deny individual rights cannot claim to be defenders of minorities.
Ayn Rand
Similar Threads
-
10/22 mods?
By xfoxracing8424x in forum RiflesReplies: 18Last Post: July 18th, 2012, 10:25 PM -
Thanks Mods!
By ungawa in forum Support & SuggestionsReplies: 2Last Post: October 1st, 2010, 11:53 AM -
car mods
By rmodel65 in forum GeneralReplies: 18Last Post: September 15th, 2009, 01:35 PM -
So I have a new job!!!!!!!!!!!!!!!!!!!!! (All I need is a little help from the mods)
By Bmarshall91 in forum GeneralReplies: 3Last Post: August 21st, 2009, 12:25 AM -
To the Mods
By larrymeyer in forum GeneralReplies: 16Last Post: May 24th, 2009, 12:52 AM
Bookmarks