Pennsylvania Firearm Owners Association

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.
Welcome to the Pennsylvania Firearm Owners Association Forum, we hope you like what you find here and we strongly encourage you to register for an account with us, especially if you are from Pennsylvania. Once registered you will have access to participate in our community. Thanks for visiting and we hope you become a regular!
Attention! There has been an influx of scammer signups!

The method of operation is to private message you and tell you that you should contact such 'n such person at a given email address.

Please report the private messages. Staff will ban the offender, and I will implement an IP ban. Unfortunately these scammers are using VPN/proxy services, which may mean your VPN/proxy may be blocked.
Attention! About VPN's and foreign IP addresses.

When signing up, do so from a US based Internet Service Provider. Turn off any VPN/safe-browsing feature. Failure to do so will result with your new account denied.

If you run into a IP ban afterwards as a member, again - turn off your VPN or switch servers. We do not ban legit Internet Service Providers from the USA(exception for certain individual IP addresses). Free VPN's tend to get banned too. We try not to ban legit subscription VPN services, but they rarely label their IP blocks correctly.

If you run into an IP ban, it likely wasn't you.

Results 1 to 2 of 2

cetme bending jig?

Thread Tools
Display
- Linear Mode
- Switch to Hybrid Mode
- Switch to Threaded Mode

June 29th, 2012, 10:20 AM #1
tonyfac

View Profile

View Forum Posts

Banned
Join Date

Feb 2010

Location

Upper Macungie, Pennsylvania
(Lehigh County)

Age

62

Posts

1,158

Rep Power

0
HK 91/G3/cetme bending jig?

Does anyone have a hk bending jig in the Lehigh Valley, or somewhere close?
i really don't need to spend $300 on one for 1 flat. hk parts is out of receivers, but have the flats, looking for a new project since Fal #4 should be done soon.
if anyone can help me out i would greatly appreciate it.
tony

Reply With Quote
June 29th, 2012, 03:26 PM #2
Zet70

View Profile

View Forum Posts

Private Message

Grand Member
Join Date

Jul 2009

Location

Reading, Pennsylvania
(Berks County)

Posts

2,322

Rep Power

8770775
Re: HK 91/G3/cetme bending jig?

I don't have one but if you're will to help me build one too I would certainly split a jig with you. And I'm in the valley as well.

Emergency Medicine prevents natural selection

Reply With Quote

Quick Navigation Gunsmithing Top

Site Areas
Settings
Private Messages
Subscriptions
Who's Online
Search Forums
Forums Home
Forums
Forum
Discussion
Law & Politics
1. Pennsylvania
2. National
Marketplace
Events
Private Forums
1. PAFOA Club
Regions
1. Lake Erie Region
  1. Crawford
  2. Erie
  3. Mercer
  4. Venango
2. Allegheny National Forest Region
  1. Cameron
  2. Clarion
  3. Clearfield
  4. Elk
  5. Forest
  6. Jefferson
  7. McKean
  8. Potter
  9. Tioga
  10. Warren
3. Valleys of the Susquehanna Region
  1. Centre
  2. Clinton
  3. Columbia
  4. Juniata
  5. Lycoming
  6. Mifflin
  7. Montour
  8. Northumberland
  9. Snyder
  10. Union
4. Pocono Mountain Region
  1. Bradford
  2. Carbon
  3. Lackawanna
  4. Luzerne
  5. Monroe
  6. Pike
  7. Schuylkill
  8. Sullivan
  9. Susquehanna
  10. Wayne
  11. Wyoming
5. Lehigh Valley & Philadelphia Region
  1. Bucks
  2. Chester
  3. Delaware
  4. Lehigh
  5. Montgomery
  6. Northampton
  7. Philadelphia
6. PA Dutch Country/Hershey Region
  1. Adams
  2. Berks
  3. Cumberland
  4. Dauphin
  5. Franklin
  6. Lancaster
  7. Lebanon
  8. Perry
  9. York
7. Laurel Highlands Region
  1. Bedford
  2. Blair
  3. Cambria
  4. Fayette
  5. Fulton
  6. Greene
  7. Huntingdon
  8. Indiana
  9. Somerset
  10. Westmoreland
8. Pittsburgh Region
  1. Allegheny
  2. Armstrong
  3. Beaver
  4. Butler
  5. Lawrence
  6. Washington
Miscellaneous
1. The Lounge

« Previous Thread | Next Thread »

Similar Threads

AK bending help

By sneeringer8372 in forum Gunsmithing

Replies: 30
Last Post: September 20th, 2011, 09:25 AM
AK-flat bending jig

By sprat in forum General

Replies: 0
Last Post: September 30th, 2009, 03:26 PM
Laws that relate to bending your own receivers / building rifles with them?

By dc dalton in forum General

Replies: 29
Last Post: July 13th, 2009, 09:26 PM
bending a hammer

By eells in forum General

Replies: 2
Last Post: April 23rd, 2009, 09:11 PM
First dry run 38 special bending brass

By gacjr in forum General

Replies: 13
Last Post: December 15th, 2008, 12:01 AM