12ga,8ga,4ga FH; 585HE/700HE; Big Bores--

[hubel458]

Some more slug experimenting and developement.
Here are pictures of the full bore Lee Key Slug
we had a guy cast. He took Lee Key mold and machined
it out to cast a .729" full bore slug.
The original Lee mold makes slugs smaller diameter,
so that they fit in a 12ga wadcup.
Slugs are hard cast alloy to take high speeds..
In picture is two MRC 2 5/8" brass 12ga cases with
slugs in them. These slugs with those brass cases are
being tested first in rifled barrels in a guys 1887 WIN,
where they needed short combination to feed from tube.
These slugs have real good shoulder step to
roll crimp against when used in plastic cases.

These first ones are 500 gr.The guys are reworking
another die to get the weight up to about 600gr,
that some of our the brass case guys want to use.
So many guys like the 600 gr size, but these with
the partly hollow base allows them to be longer,
for a little more stability,if used in smooth barrels.
Lee molds are not a real high price so it isn't
a bad deal to get them and change them.

Some newer slug ideas coming around. First is Brenneke,
a locked on base ounce slug, in sabot at factory speed of
16-1700 or so in 3" plastic.Really go in our 3.5" loads.
Brenekke has had full bore slugs with lock-on seal and
cushion, but this new appliction putting them in a sabot.
Picture #2


Third is Dupleks, steel slug riding on a plastic band,
penetrates very well. About 1 1/8 oz.And no steel touches
the bore only the plastic.Should have good penetration
witout breaking apart.These are front heavy will get
fair accuracy in smooth bores.











A new slug from the EU,a new 300gr US-S slug with locked
on base, discarding petals, by European Cartridge. Accurate
in smooth bores, Using the same idea as their all brass slugs
we showed above with locked on base, and discarding front petals.
Only these are mostly aluminum to get a lighter slug combo.In the
first picture.In 3" plastic they load to over 2100 with shotgun
powders. In a 3.5" plastic and our slower powders
we can get 2800. 2nd picture some results of penetration tests
in a sand bank they did. The brass centers penetrate like the
all brass ones they make.They are reporting 2" groups from regular
barreled smoothbore pumpguns at 50 yds with scope.Ed

[hubel458]

We are always looking for way to shoot 8 and 10s
using easy to get components,cheap, without buying
loaded rounds for big bucks, if available at all.

In 8ga falling block, plastic case got 930gr hollowbase
slug to 2300, It is a slug for 10 ga that we expanded
base a little to fit tight in 8ga wadcup. On the left in
picture. At 30 yds 3" group. Just with open sight,
About like the 10ga sight bead. There is enough hollow in
the base it flies pretty good from 8ga smooth barrel.

Along same line, in my 10ga 32" smooth bull barrel with a
750 gr .69cal hollowbase Dixie MZ slug in VP100
10ga wadcup about same speed and same accuracy.
Nice to just get a box of slugs that is in stock,
and a 2 cent cent wadcup and Fed 3.5" 10ga plastic cases
and be shooting cheap.And the cases roll crimp nice
down to these slugs...



A different, interesting style, of 12ga slug, from Russia.
First picture loaded round, in plastic, roll crimped.
Second, two types of slugs they have on the same base.
Base for rifled barrel, little smaller diameter than the
front. Looks like the roll crimp locks against
the edge of the base. Neat idea, and it could have a
flat meplat slug on the front of the base like
the US-S brass slugs from Greece are on the
plastic bases, that I have here. They must use a crimping
die with a deep hollow up in the middle. We have thought
of taking a roll crimper and putting a deeper recess
in middle to load longer nose slugs further out so as to
have more room for our slower powders...






Here is picture of a great sizer for expanded plastic
cases, a MEC Super Sizer. It operates with collets. Sizes
cases better than factory. Has the power to shrink
expanded basecups. 2nd picture is the roll crimper tool
in drill press, it does plastic cases as good a roll crimp
as the factory does.You can see couple we crimped
behind press base in picture...Ed

[hubel458]

Here is picture of 4 long cases, top being a Rocky Mtn Cartridge
3.5" turned brass 20ga. Next a RMC 3.5" turned brass 12ga.
3rd down our 3.85" 12ga FH we made from BMG brass. Bottom
a RMC 3.85" turned brass 12ga FH case.




Next picture shows one of the old ways they locked slugs
into paper cases. Many old slugs had a wide deep groove
which made it possible to crimp that way.




Next pictures shows bullet jackets made from a copper tubing caps.
Caps are the ones they solder on to copper pipes, and they made
a die and punch to form them to a good nose shape and
size. Then they fill them from rear with lead.
Example; 1/2" cap does 700cal and 12ga with
right dies and punches.






Last the 2nd gun we put the 585HE long belted case in,
a Ruger 77 bolt action. it has a heavy 585 cal barrel,
and it is a real strong action....Ed

[hubel458]

Here are couple more pictures of longer bullets
in sabots, loaded in plastic cases, with the
roll crimp down against the sabot. Both are
ideas tested by European Cartridge in Greece,
who make the US-S slugs. Both longer bullets
pictured have the locked on base that their
other US-S slugs have, for smooth bore accuracy.
2nd picture shows a deep hollow roll crimper
for doing slugs like these.Ed






We also had RMC make us a long brass 28ga case.
It is 3.25" long as shown in picture. They could be
3" or whatever you would want. The 550 Mag rifled barrels
are perfect bore for them, and we did one
in a Mossy 695 bolt gun, 2nd picture...Added heavy barrel.
It is shown next to a 505 Gibbs brass
case 1st picture to show that it isn't a puny case.
And chamber still fires plastic 28ga like the
new Brenekke slugs just out.Ed

[knight0334]

Ed,

What kind of case life are you getting out of the Rocky Mtn brass?

I'm thinking of getting a NEF/H&R 12ga slug gun and some 3" brass to use as a groundhog howitzer.

[hubel458]

With moderated loads couple dozen reloads with case
he makes for slugs with large inside corner radius.

First picture is an RC4 brand slug I see is available
down under. It has locked base like Brenekke.
And locked on without discarding petals, like US-S.

And 2nd picture is a group fired with RC4 slugs
by fellow on NitroExpress forums from a good
double 12ga, 2 left and 2 rights at 25yds.
This shows the possibilities of working with smoothbores,
rather than not trying to make them work.

3rd picture is a discarding sabot base slug, and with
four discarding sabot carriers, with centered
penetrating solid bullet, from France.Ed










In earlier thread I mentioned the long brass 28ga case
we setup. Well here is picture of a revolving 28ga
we will try to get later on and put in heavy barrel
and longer chamber and use brass 28ga cases.Ed

[hubel458]

Some more slug and sabot ideas folks are doing.

First is a long pointed slug with locked on base,
It goes to target with base,can work smoothbore.



Second is picture of Hexolit sabot base slug
with petals expanded, sure would make bad wound.



Third shows a variety of Gualandi slugs you can
get for reloading, and we're finding that these
locked base slugs, Brenekke/USS style slugs, are
giving good accuracy in smooth barrels which can
save when doing heavy barrels.Weights shown in
grams, get our weights in grains multiply by 15.4..Ed

[hubel458]

Here are some more sabot/slug and loading concepts.

First is Alcan 2.75" paper case with Dixie 600gr slug,
with the side of the case crimped into the relief/lube
groove of the Dixie slug.The groove in the Dixie isn't
quite as deep as the groove in the Fosbury slug shown
in earlier post, but still seems to crimp fairly tight.



Next are various slugs in 12ga REM sabots that take
57 cal slugs and bullets.Those sabots are from the REM
Accutip loadings. In picture you can see one of the
REM 385gr jkt bullets they use. Also is sabot
with 20ga cast Lyman. On right sabot with hardcast 585 cal
640gr lead bullet, the ones I use in my 585HE wildcat
case. I sized it down a little, perfect fit.
Also the .575 cal Dixie Gunworks lead slugs will do.

Also shown is a long pointed 55 Boys bullet in one,
fairly tight fit.We cut back .3" of bullet off so it
fit for length in sabot and is 750gr.



Third are 3.5" brass and plastic with the REM sabot and
the 750gr pointed slugs in them.In all the sabot work we
and others have done, trying to get accuracy and high
speeds together, maybe there is such a thing as too
much plastic. IE, sabots too thick on the sides if doing
50cal or smaller in 12ga sabots, for heavier slugs
at high speeds. Thinner sides may discard more evenly at
the greater pressures and violence of high speeds.
Thin sides may have less give so that sabot grips slug
better to impart spin in rifled use. Example in
smoothbore use is the USS slugs, where the brass slug
is .629" with thin discarding petals that have proven to
be very accurate. And with both reasonable priced sabot
offerings the last few years being undersize, accuracy
problems, etc, maybe time to try something else.

Got to find whole bunch of these sabots. Are these pictured
12ga REMs the only 58cal ones around? I can't find others,
and maybe we can find where these are made. As I have
huge numbers of the 585 slugs, which by the way I think
is best hunting combination, without extremely heavy slugs
which suffer for the speeds needed for longer range use.
It is hard lead, good for big game.And my guy can make many,
many more if needed whether for 585HE rifles
or in sabots if we can find some.ED

[leplat]

I thought these where all odd balls that just you make. Then I found them listed under the most powerful cartridges.

12gaFH and your 700 hubel express is listed. Good for you. I want to load one of your calibers to go after some groundhogs . Keep those pictures comming.

[hubel458]

Some more sabot and slug ideas, discarding types
and locked on base types.

First picture of 20ga Buckhamer pulled apart. The bunch
I have were pulled apart, the slug won't lock back in
tight, into the base.



Second is various 20ga sabot/slug ideas some using
buckhammer sabot bases that a bunch of 458 cal lead
slugs and jackted slugs I have, lock into real tight.
The 458 lead ones are 400gr, jkt are 350gr.

And I got some empty SPW 20 gauge sabots, and 20ga
Buckhammer slugs lock into them real tight.I have
many of these slugs. These slugs are 440gr.

Also is 3" 20ga FED factory sabot shell and one of
discarding sabots out of the case. Also a 3.5" 20ga
Hastings 3.5" load with black locked on base sabot,
and sabots out of the case and couple 20 brass
3.5" RMC cases.



Next is variety of 12ga sabots with 50cal slugs
in them.2 white and the pink sabot are FED, The black
is Hornady, With a 50cal long bullet .
The grey, is a BPI with .504" cast 440gr slug.
I wish the BPI was full size like the others
and fit rifled barrels tight for accuracy.........



Last 12ga SPWs from Slug-R-US(30 cents ea) with various
50 cal slugs locked in tight, and shown with one out of
a factory load, the dark colored one. 50cal 385gr
Great Plains ML slugs lock in perfect for a lighter
loading. Other ML slugs will do and a few of
the Dixie Gunworks 50cal slugs lock in also...Ed