Results 1 to 10 of 21
Thread: Need Gunsmith NW Lanc Co
-
September 17th, 2011, 12:16 PM #1
Need Gunsmith NW Lanc Co
Need a Gunsmith in NW Lanc Co for changing sights on handgun.
Any recommendations?
Thanks
-
September 17th, 2011, 01:57 PM #2
Re: Need Gunsmith NW Lanc Co
Encks Gun Barn
Don't sweat the petty stuff, and don't pet the sweaty stuff.
-
September 18th, 2011, 07:17 PM #3Member
- Join Date
- Mar 2007
- Location
-
Colonia,
New Jersey
- Posts
- 56
- Rep Power
- 18
Re: Need Gunsmith NW Lanc Co
Where is Encks?
-
September 20th, 2011, 08:58 AM #4
Re: Need Gunsmith NW Lanc Co
Outside Schafferstown, Lebanon County. encksgunbarn.com
Don't sweat the petty stuff, and don't pet the sweaty stuff.
-
September 20th, 2011, 03:50 PM #5
Re: Need Gunsmith NW Lanc Co
Steve at Bullseye Shooters in Elizabethtown will hook you up. I go to him for everything I need and he is absolutely amazing when it comes to his gunsmithing knowledge and abilities.
His shop is located on Market Street (PA 230) across from the Kmart in Elizabethtown.
-
September 27th, 2011, 09:41 PM #6
Re: Need Gunsmith NW Lanc Co
You could try Trop, Bullseye never gave me a call back ...
-
September 27th, 2011, 09:43 PM #7
Re: Need Gunsmith NW Lanc Co
I always seem to have a hard time actually reaching Steve by phone. Stop in his shop. That's what I do.
As far as Trop is concerned, screw everything about that place. Their prices, their staff, their attitude... All of it is about as sour as milk in the sun. It sits in your stomach about just as well, too.
-
September 29th, 2011, 12:07 PM #8
Re: Need Gunsmith NW Lanc Co
I have called Trop about this and they told me it would need to go to the factory...I was surprised because another small gun shop told me I could probably do it myself and just push out the old sights and push in the new sights by hand.
Those are two extremely opposite opinions on how to get this done. I thought I could probably do it myself exercising care, but when the Trop told me they can't do it, I figured there is no way I could do it myself if they can't even do it.
Never thought it would be this difficult to change the sights.
-
September 29th, 2011, 01:09 PM #9
Re: Need Gunsmith NW Lanc Co
What kind of handgun is it? I have just stooped in at Bullseye at least three different occasions and he just took out or put on sights for me right there on the spot... I have never been told a gun has to go bak to factory for sight installation or removal.
-
September 29th, 2011, 05:42 PM #10
Re: Need Gunsmith NW Lanc Co
M&P.
Also have an XDm and Trop said that needs to go to factory also.
Similar Threads
-
Can someone help me get to Kerpers in Lanc. county?
By bripro in forum GeneralReplies: 7Last Post: April 7th, 2012, 10:49 AM -
Remington .22 521T (target) So.Lanc.Co
By Whiskey Delta in forum GeneralReplies: 0Last Post: November 16th, 2009, 11:59 AM -
.30 Cal (30-06) M2 Ball FTF NW Lanc. Cnty
By sigarms229 in forum GeneralReplies: 0Last Post: July 17th, 2009, 10:15 PM -
Justice In Lanc. Co.
By Juztruckin in forum GeneralReplies: 3Last Post: July 22nd, 2008, 11:27 PM
Bookmarks